´1

D-Link WBR-1310 User Manual

Appendix A - Wireless Basics

Where is wireless used?

Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s

becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless

connection in public places is usually called “hotspots”.

Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote

locations like Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers.

Wireless network is easy to setup, but if you’re installing it for the first time it could be quite a task not knowing where to

start. That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless

network.

Tips

Here are a few things to keep in mind, when you install a wireless network.

Centralize your router or Access Point

Make sure you place the router/access point in a centralized location within your network for the best performance. Try

to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home.

If you have a two-story home, you may need a repeater to boost the signal to extend the range.

Eliminate Interference

Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the

router/access point. This would significantly reduce any interference that the appliances might cause since they operate

on same frequency.

´±

D-Link WBR-1310 User Manual

Appendix A - Wireless Basics

Security

Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning

on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up.

There are basically two modes of networking:

•

Infrastructure

– All wireless clients will connect to an access point or wireless router.

•

Ad-Hoc

– Directly connecting to another computer, for peer-to-peer communication, using wireless network

adapters on each computer, such as two or more WNA-2330 wireless network Cardbus adapters.

An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect

to the wireless router or access point.

An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in

Ad-Hoc mode to communicate.

Wireless Modes

´3

D-Link WBR-1310 User Manual

Appendix B - Networking Basics

Networking Basics

Check your IP address

After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a

DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.

Click on

Start

>

Run

. In the run box type

cmd

and click

OK

.

At the prompt, type

ipconfig

and press

Enter

.

This will display the IP address, subnet mask, and

the default gateway of your adapter.

If the address is 0.0.0.0, check your adapter

installation, security settings, and the settings

on your router. Some firewall software programs

may block a DHCP request on newly installed

adapters.

If you are connecting to a wireless network at a hotspot (e.g. hotel, coffee shop, airport), please contact an employee

or administrator to verify their wireless network settings.

´²

D-Link WBR-1310 User Manual

Appendix B - Networking Basics

Statically Assign an IP address

If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps

below:

Step 1

Windows

®

XP - Click on

Start

>

Control Panel

>

Network Connections

.

Windows

®

2000 - From the desktop, right-click

My Network Places

>

Properties

.

Step 2

Right-click on the

Local Area Connection

which represents your D-Link network adapter and select

Properties

.

Step 3

Highlight

Internet Protocol (TCP/IP)

and click

Properties

.

Step 4

Click

Use the following IP address

and enter an IP address that is on the same subnet as your network or the LAN

IP address on your router.

Example: If the router´s LAN IP address is 192.168.0.1, make your IP address

192.168.0.X where X is a number between 2 and 99. Make sure that the number

you choose is not in use on the network. Set Default Gateway the same as the LAN

IP address of your router (192.168.0.1).

Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The

Secondary DNS is not needed or you may enter a DNS server from your ISP.

Step 5

Click OK twice to save your settings.

´³

D-Link WBR-1310 User Manual

Appendix C - Technical Specifications

Technical Specifications

Standards

• IEEE 802.11g

• IEEE 802.11b

• IEEE 802.3

• IEEE 802.3u

Wireless Signal Rates*

• 54Mbps

• 48Mbps

• 36Mbps

• 24Mbps

• 18Mbps

• 12Mbps

• 11Mbps

• 9Mbps

• 6Mbps

• 5.5Mbps

• 2Mbps

• 1Mbps

Security

• WPA - Wi-Fi Protected Access (TKIP, MIC,

IV Expansion, Shared Key Authentication)

• 802.1x

• 64/128-bit WEP

Modulation Technology

Orthogonal Frequency Division Multiplexing (OFDM)

Receiver Sensitivity

• 54Mbps OFDM, 10% PER,-68dBm)

• 48Mbps OFDM, 10% PER,-68dBm)

• 36Mbps OFDM, 10% PER,-75dBm)

• 24Mbps OFDM, 10% PER,-79dBm)

• 18Mbps OFDM, 10% PER,-82dBm)

• 12Mbps OFDM, 10% PER,-84dBm)

• 11Mbps CCK,

8% PER,-82dBm)

• 9Mbps OFDM, 10% PER,-87dBm)

• 6Mbps OFDM, 10% PER,-88dBm)

• 5.5Mbps CCK, 8% PER,-85dBm)

• 2Mbps QPSK, 8% PER,-86dBm)

• 1Mbps BPSK, 8% PER,-89dBm)

VPN Pass Through/ Multi-Sessions

• PPTP

• L2TP

• IPSec

Device Management

• Web-based Internet Explorer v6 or later; Netscape

Navigator v6 or later; or other Java-enabled browsers

• DHCP Server and Client

Wireless Frequency Range

2.4GHz to 2.462GHz

Wireless Operating Range2

• Indoors - up to 328 ft. (100 meters)

• Outdoors- up to 1312 ft. (400 meters)

Wireless Transmit Power

15dBm ± 2dBm

External Antenna Type

Single detachable reverse SMA