Page 51 / 74 Scroll up to view Page 46 - 50
³1
D-Link WBR-1310 User Manual
Section ³ - Connecting to a Wireless Network
3.
The
Wireless Network Connection
box will appear. Enter the same
WEP key that is on your router and click
Connect
.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the WEP settings are correct. The
WEP key must be exactly the same as on the wireless router.
Page 52 / 74
³±
D-Link WBR-1310 User Manual
Section ³ - Connecting to a Wireless Network
Configure WPA-PSK
It is recommended to enable WEP on your wireless router or access point before configuring your wireless adapter. If
you are joining an existing network, you will need to know the WEP key being used.
2.
Highlight the wireless network (SSID) you would like to
connect to and click
Connect
.
1.
Open the Windows
®
XP Wireless Utility by right-clicking
on the wireless computer icon in your system tray
(lower-right corner of screen). Select
View Available
Wireless Networks
.
Page 53 / 74
³3
D-Link WBR-1310 User Manual
Section ³ - Connecting to a Wireless Network
3.
The
Wireless Network Connection
box will appear. Enter the
WPA-PSK passphrase and click
Connect
.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the WPA-PSK settings are correct.
The WPA-PSK passphrase must be exactly the same as on the
wireless router.
Page 54 / 74
³²
D-Link WBR-1310 User Manual
Section ´ - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the WBR-1310.
Read the following descriptions if you are having problems.
(The examples below are illustrated in Windows
®
XP.
If
you have a different operating system, the screenshots on your computer will look similar to the following examples.)
1. Why can’t I access the web-based configuration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website on
the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself.
Your computer must be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
• Internet Explorer 6.0 or higher
• Netscape 8 or higher
• Mozilla 1.7.12 (5.0) or higher
• Opera 8.5 or higher
• Safari 1.2 or higher (with Java 1.3.1 or higher)
• Camino 0.8.4 or higher
• Firefox 1.5 or higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using
a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may
not be on.
• Disable any internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice,
Sygate, Norton Personal Firewall, and Windows
®
XP firewall may block access to the configuration pages. Check the
help files included with your firewall software for more information on disabling or configuring it.
Page 55 / 74
³³
D-Link WBR-1310 User Manual
Section ´ - Troubleshooting
• Configure your Internet settings:
• Go to
Start
>
Settings
>
Control Panel
. Double-click the
Internet Options
Icon. From the
Security
tab,
click the button to restore the settings to their defaults.
• Click the
Connection
tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings
button. Make sure nothing is checked. Click
OK
.
• Go to the
Advanced
tab and click the button to restore these settings to their defaults. Click
OK
three
times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address
bar. This should open the login page for your the web management.
• If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait
about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different
computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back
to the factory defaults.
To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a
paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process.
Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is
admin
and leave the password box empty.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top