D-Link GO-RT-N150 Router Manual PDF (Setup & Configuration Guide)

Page 41 / 73 Scroll up to view Page 36 - 40

37

D-Link GO-RT-N150 User Manual

Section 3 - Conﬁguration

To use the Universal Plug and Play (UPnP) feature

click

Enable UPnP

. UPnP provides compatibility

with networking equipment, software and

peripherals.

Unchecking the box will not allow the router to

respond to pings. Blocking the ping may provide

some extra security from hackers. Check the box

to allow the Internet port to be “pinged”.

You may set the port speed of the Internet port

to 10Mbps, 100Mbps, or auto. Some older cable

or DSL modems may require you to set the port

speed to 10Mbps.

UPnP Settings:

Enable WAN

Ping Response:

WAN Port

Speed:

Advanced Network Settings

Page 42 / 73

38

D-Link GO-RT-N150 User Manual

Section 3 - Conﬁguration

Enter a new password for the Administrator Login

Name. The administrator can make changes to the

settings.

Remote management allows the router to be

conﬁgured from the Internet by a web browser. A

username and password is still required to access

the Web-Management interface. In general, only

a member of your network can browse the built-

in web pages to perform Administrator tasks. This

feature enables you to perform Administrator tasks

from the remote (Internet) host.

The port number used to access the router.

Admin Password:

Remote

Management:

Remote Admin

Port:

Tools

Administrator Settings

This page will allow you to change the administrator and user passwords. You can also enable Remote Management.

There are

two accounts that can access the management interface through the web browser. The accounts are admin and user. Admin

has read/write access while user has read-only access. User can only view the settings but cannot make any changes. Only the

admin account has the ability to change both admin and user account passwords.

Page 43 / 73

39

D-Link GO-RT-N150 User Manual

Section 3 - Conﬁguration

Time Settings

Select the Time Zone from the drop-down menu.

To select Daylight Saving time manually, select

enabled or disabled, and enter a start date and an

end date for daylight saving time.

Press this button to set the device’s time to match

a local PC.

NTP stands for Network Time Protocol. NTP

synchronizes computer clock times in a network

of computers. Check this box to use a NTP server.

This will only connect to a server on the Internet,

not a local server.

Enter the NTP server or select one from the drop-

down menu. The router will sync the same time to

D-Link Internet time server.

To manually input the time, enter the values in

these ﬁelds for the Year, Month, Day, Hour, Minute,

and Second and then click

Save Settings

.

Time Zone:

Daylight Saving:

Sync your

Computer’s Time

Settings:

Enable NTP

Server:

NTP Server Used:

Manual:

The Time Conﬁguration option allows you to conﬁgure, update, and maintain the correct time on the internal system clock.

From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be conﬁgured to

automatically adjust the time when needed.

Page 44 / 73

40

D-Link GO-RT-N150 User Manual

Section 3 - Conﬁguration

Use this option to save the current router

conﬁguration settings to a ﬁle on the hard disk of

the computer you are using. First, click the

Save

button. You will then see a ﬁle dialog, where you

can select a location and ﬁle name for the settings.

Use this option to load previously saved router

conﬁguration settings. First, use the Browse control

to ﬁnd a saved conﬁguration settings ﬁle. Then,

click the

Load

button to transfer those settings to

the router.

This option will restore all conﬁguration settings

back to the those that were in eﬀect at the time the

router was shipped from the factory. Any settings

that have not been saved will be lost, including any

rules that you have created. If you want to save the

current router conﬁguration settings, use the

Save

button above.

Click to reboot the router.

This is to restore the device back to the English

version only. Remove other languages installed

for the system web pages.

Save Settings

to Local Hard

Drive:

Load Settings

from Local Hard

Drive:

Restore to

Factory Default

Settings:

Reboot Device:

Clear Language

Pack:

System Settings

Page 45 / 73

41

D-Link GO-RT-N150 User Manual

Section 3 - Conﬁguration

Displays the current ﬁrmware version and date.

After you have downloaded the new ﬁrmware,

click

Browse

to locate the ﬁrmware update on

your hard drive.

Click

Upload

to complete the

ﬁrmware upgrade.

This function allows the user to change the

language of GUI from the default English to

another language by upgrading the language

pack.

Firmware

Information:

Firmware

Upgrade:

Language Pack

Upgrade:

Update Firmware

You can upgrade the ﬁrmware of the router here. Make sure the ﬁrmware ﬁle you want to use is on the local hard drive of the

computer. Click on

Browse

to locate the ﬁrmware ﬁle to be used for the update. Please check the D-Link support site at

http://

support.dlink.com

for ﬁrmware updates. You can download ﬁrmware upgrades to your hard drive from the D-Link support site.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share