1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DWL-P1012
    5. /
  5. 4
Page 16 / 51 Scroll up to view Page 11 - 15
12
C
ONFIGURATION
Through the Web Browser you can configure the DWL-P1012’s PoE power
management configuration.
With the attached Web Management Utility, you can easily discover all DWL-
P1012 units on the network, assign them IP Addresses, change the
administrative passwords and upgrade firmware.
Installing the Web Management Utility
Follow these instructions to install and use the Web Management utility.
1.
Insert the DWL-P1012 Master CD in the CD-Rom Drive.
2.
Allow the CD to Autorun. From the Autorun menu select the option to
install the utility.
Skip to step 4.
If the Menu does not automatically appear,
go to the Start menu on the Windows desktop, then choose Run.
3.
In the Run dialog box, type D:\Web Management Utility\setup.exe (D:\
depends where your CD-Rom drive is located) and click OK.
4.
Follow the on-screen instructions to install the utility.
5.
Upon completion, go to Program Files -> web_management_utility and
execute the Web Management utility.
The Web Management Utility is
divided into four sections:
Discovery List, Monitor List,
Device Setting
and
Toolbar
function. For detailed instructions,
refer to the corresponding section
in the following pages.
Page 17 / 51
13
Discovery List
This is the list where you can discover all the Web management devices on the
network.
By pressing the “Discovery” button, you initiate the discovery process which will
find any available Web Smart devices connected to the same LAN as the PC
running the Utility and list them.
Double click or press the “Add to monitor list” button to transfer a device from
the Discovery List to the Monitor List.
System Term definitions in the Discovery List:
±
MAC Address:
Shows the device MAC Address.
±
IP Address:
Shows the current IP address of the device.
±
Protocol version:
Shows the version of the Utility protocol.
±
Product Name:
Shows the device product name.
±
System Name:
Shows the appointed device system name.
±
Location:
Shows where the device is located.
±
Trap IP:
Shows the SNMP Trap Host IP.
±
Subnet Mask:
Shows the Subnet Mask of the device.
±
Gateway:
Shows the Default Gateway of the device.
Page 18 / 51
14
Monitor List
All Web Smart Devices in the Monitor List can be monitored; you can also
receive SNMP traps and show the status of each device.
System word definitions in the Monitor List:
±
S:
Shows the system symbol of the Web-Smart device,
represent
for device system is not active.
±
IP Address:
Shows the current IP address of the device.
±
MAC Address:
Shows the device MAC Address.
±
Protocol version:
Shows the version of the Utility protocol.
±
Product Name:
Shows the device product name.
±
System Name:
Shows the appointed device system name.
±
Location:
Shows where the device is located.
±
Trap IP:
Shows the IP where the Trap to be sent.
±
Subnet Mask:
Shows the Subnet Mask set of the device.
±
Gateway:
Shows the Gateway set of the device.
View Trap:
The Trap function can receive and display the events that issue
SNMP traps from the DWL-P1012 in the Monitor List.
There is an indicator light on the “View Trap” button. When this indicator is
green, there is no new trap message. When the indicator is red, a new trap has
been issued, this is to remind us to view the trap.
When the “View Trap” button is clicked, a Trap Information window will pop out
that shows the trap information including Symbol, Time, Device IP and the
Event occurred.
Page 19 / 51
15
The symbol “
” represents a new trap signal has arisen, this symbol will
disappear after you review and click on the event record.
Add Item:
To add a device to the Monitor List manually, enter the IP Address of
the device that you want to monitor.
Delete Item:
To delete the device in the Monitor List.
Note:
In order to receive Trap information using the utility, the DWL-P1012 has
to be configured with the appropriate Trap IP and Trap Events first.
Device Setting
You may configure the device by using the function key in the Device Setting
Dialog box.
Configuration Setting:
In the Configuration Setting, you may configure the IP
Address, Subnet Mask, Default Gateway, Set Trap to (Trap Host IP Address),
System name and Location.
Select the device in the Discovery list or Monitor List and press this button, then
the Configuration Setting window will pop out as
Error! Reference source not
found.
, after filling up the data that you want to change, you must fill up the
password and press the “Set” to process the data changed immediately.
Page 20 / 51
16
Password Change:
You can use the Password Change dialog when you need
to change the password. Fill in the new and old passwords and press “Set”
button to apply the password change immediately.
Firmware Upgrade:
If D-Link releases firmware to support new functions, the
new firmware can be uploaded through here.
Web Access:
Double click the device in the Monitor List or select a device in
the Monitor List and press the “Web Access” button to access the device
through a Web browser.
Toolbar
The toolbar in the Web Management Utility have four main tabs:
File, View,
Options
and
Help
.

Rate

124.8 / 5 based on 304 votes.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top