D-Link DWL-G820v2 Router Manual PDF (Setup & Configuration Guide)

Page 11 / 34 Scroll up to view Page 6 - 10

11

Requirements for using the DWL-G820’s Web

Configuration Utility

Using the Configuration Menu

The DWL-G820 must be connected directly to your computer

for configuration. You cannot configure this device if it is

connected to a hub or router.

If you are incorporating the DWL-G820 into a network that contains all D-Link

devices, you do not need to use the Web Configuration utility. With its default

settings, the DWL-G820 will connect with other D-Link 802.11b or 802.11g devices

that are set to their default settings, with no configuration needed!

If your network contains devices other than D-Link devices, or if you wish to configure

the DWL-G820, you will need to do the following before using the Web Configuration

Utility:

You will need a Java-enabled Web browser such as the Internet Explorer

6.0 or later, or the Netscape Navigator 6.0 or later.

You will need to assign a static IP address to the computer that you are

using to configure the DWL-G820, within the IP address range of the

DWL-G820. The DWL-G820 has a default IP address of

192.168.0.35

with

a subnet mask of 255.255.255.0

You can, for example, assign a static IP address of 192.168.0.2 with a subnet

mask of 255.255.255.0 to the computer you will use for configuration.

(Please refer to the Appendix section of the Quick Installation Guide.)

Factory Default Settings for the DWL-G820

Operating Mode:

Infrastructure

SSID:

default

Channel:

6

Transmission rates:

Auto

Encryption:

Blank

(no password needed)

Administrator Password:

No

IP Address Mode:

Static

IP Address:

IP Subnet:

username:

admin

255.255.255.0

192.168.0.35

Page 12 / 34

12

±

Note: if you have changed the default IP address assigned to the DWL-G820, make sure to

enter the correct IP address.

Using the Configuration Menu (continued)

Home > Wizard

The

Home>Wizard

screen will appear.

Please refer to the

Quick

Installation Guide

for

more information regarding

the Setup Wizard.

After you have completed the

Setup Wizard

(please see the

Quick Installation Guide

that

came with the product) you can access the

Configuration

menu at any time by opening

the Web browser and typing in the IP address of the DWL-G820. The DWL-G820 default

IP address is shown below:

±

Open the Web browser

±

Type in the

IP address

of the

DWL-G820

±

Type

admin

in the

User Name

field

Leave the

Password

blank.

(However, if you have changed

the password, please enter the

correct password.)

Click

OK

admin

http://192.168.0.35

DWL-G820

Page 13 / 34

13

Using the Configuration Menu (continued)

Home > Wireless

Channel-

6

is the default channel. All devices on the network must share the

same channel.

Wireless

Band-

IEEE802.11g.

SSID-

Service Set Identifier (SSID) is the name designated for a specific wireless

local area network (WLAN). The SSID’s factory default setting is

default.

The SSID can be easily changed to connect to an existing wireless network or

to establish a new wireless network.

Radio

Frequency-

The radio frequency will remain at 2.437GHz.

Apply-

Click

Apply

to save the changes.

Page 14 / 34

14

Using the Configuration Menu (continued)

Home > LAN

LAN is short for Local Area Network. This is considered your internal network. These are

the IP settings of the LAN interface for the DWL-G820. These settings may be referred to

as private settings. You may change the LAN IP address if needed. The LAN IP address

is private to your internal network and cannot be seen on the Internet.

Click

Apply

to save the changes.

Get IP From-

Select

Static (Manual)

or

Dynamic (DHCP)

as the method you

will use to assign an IP address to the DWL-G820.

Apply-

Default Gateway-

This field is optional. Enter in the lP address of the router on your

network.

Subnet Mask-

The subnet mask of the LAN interface.

The default subnet mask is

255.255.255.0

IP Address-

The IP address of the LAN interface. The default IP address is:

192.168.0.35

Page 15 / 34

15

Using the Configuration Menu (continued)

Advanced > Mode

Service Type-

AP Client

Apply

-

MAC Address

- Media Access Control Address

A unique hardware address that identifies a device on a network. It is assigned at

the factory and cannot be changed. Usually you will find this address on a sticker

on the device or on the packaging.

Site Survey-

An Infrastructure

network includes a

router or an access

point; an Ad-Hoc

network is a Peer-to-Peer

network with a

direct communication

between two DWL-G820s.

Root AP MAC

Address-

SSID-

In Infrastructure mode:

Enter the MAC Address of the access point or

router in your network.

In Ad-Hoc mode:

Enter the IP address of the DWL-G820 that you will be

in Peer-to-Peer communication with.

Select

Infrastructure

or

Ad-Hoc

.

In Infrastructure mode:

Enter the SSID of the access point or router in

your network.

In Ad-Hoc mode:

Enter the SSID of the DWL-G820 that you will be in

Peer-to-Peer communication with.

Click

Site Survey

to view the available networks

Click

Apply

if you have made any changes.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share