Page 76 / 83
Scroll up to view Page 71 - 75
74
<
ENTER
> buttons to start recording the disconnect tone.
9.
Please hang up the phone if you get the message as below
：
Analizing!! Please
wait a moment…
10. There are three values you will get after analyzing. Please leave the value
which is over 1000 Hz, this is not the frequency of disconnect tone.
11. Please put the frequency in the tone table just follow the command
：
tone 4 420 680 8 8 25 25 50 50
【
Example-1
】
(Make a call from PSTN to FXO port)
usr/config$ record -tone
Press (R) to start record...
(Please make sure that you are already finish the steps 2 ~ 7)
r
(Press “Enter” button after you key in “R”)
....................................................................................................
....................................................................................................
....................................................................................................
............
Analizing!! Please wait a moment...
(You coule hang up the call from PSTN if you get this message)
Frequency 1 : 481
Frequency 3 : 621
0.25sec on 0.25sec off
tone 4 481 621 8 8 25 25 1023 1023
(Put this value in to the tone table)
tone –print
Disconnect tone 1 paramter
Frequency high
: 620
frequency low
: 480
frequency high level
: 8
frequency low level
: 8
Page 77 / 83
75
Tone1 on
: 25
Tone1 off
: 25
Tone2 on
: 1023
Tone2 off
: 1023
Disconnect tone 2 paramter
Frequency high
: 450
frequency low
: 0
frequency high level
: 8
frequency low level
: 0
Tone1 on
: 35
Tone1 off
: 35
Tone2 on
: 1023
Tone2 off
: 1023
Disconnect tone 3 paramter
Frequency high
: 620
frequency low
: 480
frequency high level
: 8
frequency low level
: 8
Tone1 on
: 50
Tone1 off
: 50
Tone2 on
: 1023
Tone2 off
: 1023
Disconnect tone 4 paramter
Frequency high
: 621
frequency low
: 481
frequency high level
: 8
frequency low level
: 8
Tone1 on
: 25
Tone1 off
: 25
Tone2 on
: 50
Tone2 off
: 50
(Confirm the values is correct or not)
(Key in the commit and reboot command if you finish the procedures as above)
【
Example-2
】
Page 78 / 83
76
(Make a call into FXO port)
usr/config$ record -tone
Press (R) to start record...
(Please make sure that you are already finish the steps 2 ~ 7)
r
(Press “Enter” button after you key in “R”)
....................................................................................................
....................................................................................................
....................................................................................................
............
Analizing!! Please wait a moment...
(You could hang up the call from PSTN if you get this message)
Frequency 1 : 473
Frequency 2 (2623) is more than 1000, please ignore it.
0. 25sec on 0.25sec off
tone 4 473 473 8 8 25 25 1023 1023
(Please configure the high and low frequency as the same value if you just get a
singal frequency)
tone –print
Disconnect tone 1 paramter
Frequency high
: 620
frequency low
: 480
frequency high level
: 8
frequency low level
: 8
Tone1 on
: 25
Tone1 off
: 25
Tone2 on
: 1023
Tone2 off
: 1023
Disconnect tone 2 paramter
Frequency high
: 450
Page 79 / 83
77
frequency low
: 0
frequency high level
: 8
frequency low level
: 0
Tone1 on
: 35
Tone1 off
: 35
Tone2 on
: 1023
Tone2 off
: 1023
Disconnect tone 3 paramter
Frequency high
: 620
frequency low
: 480
frequency high level
: 8
frequency low level
: 8
Tone1 on
: 50
Tone1 off
: 50
Tone2 on
: 1023
Tone2 off
: 1023
Disconnect tone 4 paramter
Frequency high
: 473
frequency low
: 473
frequency high level
: 8
frequency low level
: 8
Tone1 on
: 25
Tone1 off
: 25
Tone2 on
: 50
Tone2 off
: 50
(Confirm the values is correct or not)
(Key in the commit and reboot command if you finish the procedures as above)
4.2.21 [tos]
IP Packet ToS(type of Service)/Differentiated Service configuration.
-----------------------------------------------------------------------------------------------
usr/configtos
IP Packet ToS(type of Service)/Differentiated Service configuration
Usage:
tos [-rtptype dscp]
Page 80 / 83
78
tos [-sigtype dscp]
tos -print
[-rtpreliab mode]
tos -print
Example:
tos -rtptype 7 -sigtype 0
Parameter Usages:
-rtptype
the packages of voice
-sigtype
the package of call signal
Note:
The value of rtptype and sigtype is from 0 to 63.
It’s working if it supported by your network.
4.2.22 [pt]
RTP payload type configuration and information
-------------------------------------------------------------------------------------------------
usr/config$ pt
RTP payload type configuration and information
Usage:
pt -print
Display the RTP payload type information
-rfc2833
Configurate the DTMF RFC2833 payload type
-dtmf
Configurate the DTMF payload type
-fax
Configurate the FAX payload type
-faxbypass
Configurate the FAX ByPass payload type
-modembypass
Configurate the MODEM ByPass payload type
-redundancy
Configurate the Redundancy payload type
-modemrelay
Configurate the MODEM Relay payload type
Example:
pt -rfc2833 96 -fax 101
usr/config$
19216811.live