D-Link DSL-2870B Dual Band Wireless N750 Gigabit ADSL2+ Modem Router User Manual

Error! Use the Home tab to apply

标题

1 to the text that you want to appear

here.

Page 11

Information you will need about this Router

Username

This is the Username needed access the router

’s

web management interface. When you attempt to connect to the device through a web browser you will be prompted to

enter this Username. The default Username for the router

is “

admin

”

.

Password

This is the Password you will be prompted to enter when you access the router

’s

web management interface. The default Pass

word is “

admin

”

.

LAN IP Addresses for the DSL-2870B

This is the IP address you will enter into the Address field of your web browser to access the router

’s configuration

Graphical User Interface (GUI) using a web browser. The

default IP address is

192.168.1.1

. This may be changed to suit any IP address scheme the user desires. This address will be the base IP address used for DHCP service on

the LAN when DHCP is enabled.

LAN Subnet Mask for the DSL-2870B

This is the subnet mask used by the DSL-2870B, and will be used throughout your LAN. The default subnet mask is

255.255.255.0

. This can be changed later.

Information you will need about your LAN or computer

Ethernet NIC

If your computer has an Ethernet NIC, you can connect the DSL-2870B to this Ethernet port using an Ethernet cable. You can also use the Ethernet ports on the DSL-2870B

to connect to other computer or Ethernet devices.

DHCP Client status

Your DSL-2870B ADSL router is configured, by default, to be a DHCP server. This means that it can assign an IP address, subnet mask, and a default gateway address to

computers on your LAN. The default range of IP addresses the DSL-2870B will assign are from

192.168.1.2 to 192.168.1.254

. Your computer (or computers) needs to be

configured to obtain an IP address automatically (that is, they need to be configured as DHCP clients.)

Once you have the above information, you are ready to setup and configure your DSL-2870B ADSL router.

D-Link DSL-2870B Dual Band Wireless N750 Gigabit ADSL2+ Modem Router User Manual

Error! Use the Home tab to apply

标题

1 to the text that you want to appear

here.

Page 12

Device Installation

The DSL-2870B connects two separate physical interfaces, an ADSL (WAN) and an Ethernet (LAN) interface. Place the router in a location where it can be connected to the

various devices as well as to a power source. The router should not be located where it will be exposed to moisture or excessive heat. Make sure the cables and power cord

are placed safely out of the way so they do not create a tripping hazard. As with any electrical appliance, observe common sense safety procedures.

The router can be placed on a shelf or desktop, ideally you should be able to see the LED indicators on the front if you need to view them for troubleshooting.

Power on Router

The router must be used with the power adapter included with the device.

1.

Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the router and plug the adapter into a suitable nearby power source.

2.

Press the Power button into the on position. You should see the Power LED indicator light up and remain lit.

3.

If the Ethernet port is connected to a working device, check the Ethernet LED indicators to make sure the connection is valid. The router will attempt to establish the

ADSL connection, if the ADSL line is connected and the router is properly configured this should light up after several seconds. If this is the first time installing the

device, some settings may need to be changed before the router can establish a connection.

Factory Reset Button

The router may be reset to the original factory default settings by using a ballpoint pen or paperclip to gently push down the reset button in the following sequence:

1.

Press and hold the reset button while the device is powered on for 10-15 seconds.

2.

Release the reset button.

Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings. The device settings will be restored to the

factory default IP address

192.168.1.1

and the subnet mask is

255.255.255.0.

The default management u

sername is “

admin

” and the default

p

assword is “

admin

”

.

D-Link DSL-2870B Dual Band Wireless N750 Gigabit ADSL2+ Modem Router User Manual

Error! Use the Home tab to apply

标题

1 to the text that you want to appear

here.

Page 13

Network Connections

Connect ADSL Line

Use the ADSL cable included with the router to connect it to a telephone wall socket or receptacle. Plug one end of the cable into the ADSL port (RJ-11 receptacle) on the

rear panel of the router and insert the other end into the RJ-11 wall socket. If you are using a low pass filter device, follow the instructions included with the device or given to

you by your service provider. The ADSL connection represents the WAN interface, the connection to the Internet. It is the phy

sical link to the service provider’s network

backbone and ultimately to the Internet.

Connect Router to Ethernet

The router may be connected to a single computer or Ethernet device through the Ethernet ports on the rear panel. Any connection to an Ethernet concentrating device such

as a switch or hub must operate at a speed of 10/100/1000Mbps. When connecting the router to any Ethernet device that is capable of operating at speeds higher than

10Mbps, be sure that the device has auto-negotiation (NWay) enabled for the connecting port. Use standard twisted-pair cable with RJ-45 connectors. The RJ-45 ports on the

router are a crossed port (MDI-X). Follow standard Ethernet guidelines when deciding what type of cable to use to make this connection. When connecting the router directly

to a PC or server use a normal straight-through cable. You should use a crossed cable when connecting the router to a normal (MDI-X) port on a switch or hub. Use a normal

straight-through cable when connecting it to an uplink (MDI-II) port on a hub or switch. The rules governing Ethernet cable lengths apply to the LAN to router connection. Be

sure that the cable connecting the LAN to the router does not exceed 100 meters.

Hub or Switch to Router Connection

Connect the router to an uplink port (MDI-II) on an Ethernet hub or switch with a straight-through cable. If you wish to reserve the uplink port on the switch or hub for another

device, connect to any on the other MDI-X ports (1x, 2x, etc.) with a crossed cable.

Computer to Router Connection

You can connect the router directly to an Ethernet adapter card (NIC) installed on a PC using the Ethernet cable provided.

D-Link DSL-2870B Dual Band Wireless N750 Gigabit ADSL2+ Modem Router User Manual

Error! Use the Home tab to apply

标题

1 to the text that you want to appear

here.

Page 14

D-Link One-Touch APP

D-Link offers you a fast and easy way to get connected, by utilizing the free One-Touch APP for your Android or iOS mobile device which walks you step-by-step through

installation of your D-Link One-Touch enabled device.

You also have the ability to configure/change WAN and Wi-Fi settings and even upgrade the firmware.

You can search for the D-Link One-Touch APP directly in the Google Play or iOS

APP Store, and install it.

The D-Link One-Touch icon will be displayed in the mobile device (Android, iOS).

Note

:



The following steps are for the Android version of the app.



From your iOS mobile device, choose

Settings

, and Click

Wi-Fi

, select the Wi-

Fi Network Name that you created during setup and then enter default Wi-Fi

password located on your Wi-Fi configuration note.

D-Link DSL-2870B Dual Band Wireless N750 Gigabit ADSL2+ Modem Router User Manual

Error! Use the Home tab to apply

标题

1 to the text that you want to appear

here.

Page 15

1. Tap on the One-Touch icon, the following screen will appear.