What can I do if my Router is not working correctly?
There are a few quick steps you can take to try and resolve any issues:
Follow the directions in Question 2 to reset the Router.
Check that all the cables are firmly connected at both ends.
Check the LEDs on the front of the Router. The Power indicator should be on, the Internet indicator should flash, and the DSL and LAN indicators
should be on as well.
Please ensure that the settings in the Web-based configuration manager, e.g. ISP username and password, are the same as the settings that have
been provided by your ISP.
Why can’t I get an Internet connection?
For ADSL ISP users, please contact your ISP to make sure the service has been enabled/connected by your ISP and that your ISP username and password are
correct.
Page 117 / 128
D-Link DSL-2760U USER’S MANUAL
117
What can I do if my Router can’t be detected by running the installation CD?
Ensure the Router is powered on.
Check that all the cables are firmly connected at both ends and all LEDs work correctly.
Ensure only one network interface card on your PC is activated.
Click
Start
>
Control Panel
>
Security Center
to disable the firewall.
NOTE:
There is a potential security issue if the firewall is disabled on your PC. Please remember to turn it back on once you have finished the whole installation
procedure. This will enable you to be able to surf the Internet without any problem.
Page 118 / 128
D-Link DSL-2760U USER’S MANUAL
118
Knowledge Base
Check Your IP Address
After you install your new D-Link adapter, by default, the TCP/IP settings
should be set to obtain an IP address from a DHCP server (i.e. wireless
router) automatically. To verify your IP address, please follow the steps
below.
Click
Start
>
Run
. In the run box type
cmd
and click
OK
.
At the prompt, type
ipconfig
and press the
Enter
key.
This will display the IP address, subnet mask, and the default
gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation, security
settings, and the settings on your router. Some firewall software
programs may block a DHCP request on newly installed adapters.
If you are connecting to a wireless network at a hotspot (e.g. hotel,
coffee shop, airport), please contact an employee or administrator
to verify their wireless network settings.
Page 119 / 128
D-Link DSL-2760U USER’S MANUAL
119
Statically assign an IP Address
If you are not using a DHCP capable gateway/router, or you need to assign a
static IP address, please follow the steps below:
Step 1
Windows® XP - Click
Start
>
Control Panel
>
Network Connections
.
Windows® 2000 - From the desktop, right-click
My Network Places
>
Properties
.
Step 2
Right-click
Local Area Connection
which represents your D-Link network
adapter and select Properties.
Step 3
Select
Internet Protocol (TCP/IP)
in the list and click the
Properties
button.
Step 4
Click the
Use the following IP address
and enter an IP address that is on the same subnet as your network or the LAN IP address on your router.
Example: If the router’s LAN IP address is 192.168.1.1, make your IP address 192.168.1.X where X is a number between 2 and 99. Make sure that the number
you choose is not in use on the network. Set Default Gateway the same as the LAN IP address of your router (192.168.1.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.1.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP.
Step 5
Click
OK
twice to save your settings.
Page 120 / 128
D-Link DSL-2760U USER’S MANUAL
120
Technical Specifications
DEVICE INTERFACES
RJ-11 ADSL port
4 x RJ-45 10/100BASE-TX Ethernet ports with auto MDI/MDIX
2 x USB (Type A connector) ports
Built-in draft 802.11n wireless LAN
Factory reset button
WIRELESS LAN
802.11b/g standards, 802.11n draft 2.0
Wireless speed: up to 54Mbps (802.11g), 130Mbps (802.11n)
Frequency range: 2.4 GHz to 2.484G Hz
WEP 64/128 bits data encryption
WPA/WPA2 (Wi-Fi Protected Access) security
Multiple SSID
802.11e Wireless QoS (WMM/WME)
MAC address-based access control
ADSL STANDARDS
ADSL standards: Multi-mode, ANSI T1.413 Issue 2, ITU G.992.1
(G.dmt) Annex A, ITU G.992.2 (G.lite) Annex A, ITU G.994.1 (G.hs)
ADSL2 standards: ITU G.992.3 (G.dmt.bis) Annex A/L/M, ITU
19216811.live