D-Link DSL-2730U Router Manual PDF (Setup & Configuration Guide)

Page 21 / 87 Scroll up to view Page 16 - 20

4.3.2

Internet Setup

Choose

Setup

>

Internet Setup

. The page as shown in the right figure

appears. In this page, you can configure the WAN interface of the device.

DSL-2730U User Manual

18

Page 22 / 87

Click

Add in “INTERNET SETUP”

. The page shown in the following figure

appears.

Field

Description

PVC

Settings



The virtual path between two points in an ATM

network and its valid value is from 0 to 255.



The virtual channel between two points in an ATM

network, ranging from 32 to 65535 (0 to 31 is

reserved for local management of ATM traffic).

Service

Category

You can select from the drop-down list.

Protocol

You can select from the drop-down list.

QoS

scheduler

You can select one of the item between

Strict Priority

and

Weighted Fair Queuing

.

Encapsulati

on Mode

Select the method of encapsulation provided by your

ISP. You can select from the drop-down list.

DSL-2730U User Manual

19

Page 23 / 87

Click

DSL-2730U User Manual

20

Page 24 / 87

If you select the

PPP over Ethernet (PPPoE)

or

PPP over ATM (PPPoA)

as

the connection protocol, the following page appears.



PPP Username:

The correct user name that your ISP provides to you.



PPP Password:

The correct password that your ISP provides to you.



Authentication Method:

The value can be AUTO, PAP, CHAP, or

MSCHAP. Usually, you can select AUTO.



Dial on demand (with idle timeout timer):

If this function is enabled,

you need to enter the idle timeout time. Within the preset minutes, if the

router does not detect the flow of the user continuously, the router

automatically stops the PPPoE connection. Once it detects the flow (like

access to a webpage), the router restarts the PPPoE dialup.

If this function is disabled, the router performs PPPoE dial-up all the

time. The PPPoE connnection does not stop, unless the router is

powered off and DSLAM or uplink equipment is abnormal.



MTU Size:

Maximum Transmission Unit. Sometimes, you must modify

this function to access network successfully.



PPP IP extension:

If this function is enabled, the WAN IP address

obtained by the router through built-in dial-up can be directly assigned to

the PC being attached to the router (at this time, the router connects to

only one PC). From the aspect of the PC user, the PC dials up to obtain

an IP addres. But actually, the dial-up is done by the router. If this

function is disabled, the router itself obtains the WAN IP address.



Use Static IP Address:

If this function is disabled, the router obtains an

IP address assigned by an uplink equipment such as BAS, through

PPPoE dial-up.

If this function is enabled, the router uses this IP address as the WAN IP

address.



Enable NAT:

Select it to enable the NAT functions of the router. If you do

not want to enable NAT and wish the router user to access the Internet

normally, you must add a route on the uplink equipment. Otherwise, the

access to the Internet fails. Normally, NAT should be enabled.



Enable Firewall:

Enable or disable IP filtering.



Enable IGMP Multicast

: IGMP proxy. For example, if you wish that the

PPPoE mode supports IPTV, enable this function.

DSL-2730U User Manual

21

Page 25 / 87

If you select the

MAC Encapsulation Routing(MER)

as the connection

protocol, the following page appears.



Obtain an IP address automatically:

The modem obtains a WAN IP

address automatically and at this time it enables DHCP client functions.

The WAN IP address is obtained from the uplink equipment like BAS and

the uplink equipment is required to enable the DHCP server functions.



Use the following IP address:

If you want to manually enter the WAN IP

address, select this check box and enter the information in the field.



WAN IP Address:

Enter the IP address of the WAN interface provided by

your ISP.



WAN Subnet Mask:

Enter the subnet mask concerned to the IP address

of the WAN interface provided by your ISP.



Default Gateway

: Enter the default gateway.



Obtain DNS info automatically from WAN interface:

You can get DNS

server information from the selected WAN interface



Use the following Static DNS IP address:

If you want to manually enter

the IP address of the DNS server, select this check box and enter the

information in the fields.



Primary DNS server:

Enter the IP address of the primary DNS server.



Secondary DNS server:

Enter the IP address of the secondary DNS

server provided by your ISP.

DSL-2730U User Manual

22

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share