Page 36 / 109
Scroll up to view Page 31 - 35
Section 3 – Configuration
D-Link DSL-2642B User Manual
35
PPP Username:
Enter the account username in here.
PPP Password:
Enter the account password in here.
Authentication Method:
Choose the appropriate authentication method
here. If not sure leave this option on
Auto
.
Enable NAT:
Tick this option to enable NAT for this connection.
Enable Fullcone NAT:
Tick this option to enable Fullcone NAT for this
connection.
Enable Firewall:
Tick this option to enable firewall for this connection.
Dial on demand:
Tick this option to enable dial on demand for this
connection.
Inactivity Timeout:
The option appears when
Dial on demand
is
selected. Enter an inactivity timeout value here. Leave this option on 0 to
disable this option.
Use Static IPv4 Address:
Tick this option to use a Static IP version 4
address for this connection.
IPv4 Address:
The option appears when
Use Static IPv4 Address
is
selected. Enter the Static IP version 4 address used here.
Enable IGMP Multicast:
Tick this option to allow IGMP packets to go
through the WAN interface in both directions.
Page 37 / 109
Section 3 – Configuration
D-Link DSL-2642B User Manual
36
Selected WAN Interface:
Use the drop-down menu to choose the WAN
interface to use this connection.
Obtain DNS info from a WAN interface:
Click the radio button to obtain
DNS Server IP addresses automatically from the ISP.
User the following Static DNS IP address:
click the radio button to
manually enter the Primary and Secondary DNS Server IP addresses for
this connection.
Click the
Apply
button to accept these changes.
Click the
Cancel
button to discard these changes.
Page 38 / 109
Section 3 – Configuration
D-Link DSL-2642B User Manual
37
IP over ATM (IPoA)
VPI:
Enter the correct VPI used here.
VCI:
Enter the correct VCI used here.
Select DSL Link Type:
Select the correct DSL Link Type here. For
PPPoE, IPoE and Bridge Modes, select EoA. Click the
IPoA
radio
button to configure IPoA mode.
Encapsulation Mode:
Choose the appropriate Encapsulation Mode
here.
Service Category:
Choose the appropriate Service Category here.
Enable Quality of Service:
Tick this option to enable Quality of Service.
Enter Service Configureation:
Choose the appropriate WAN Service
Type here.
WAN IP Address:
Enter the WAN IP address used here.
WAN Subnet Mask:
Enter the subnet of the WAN IP address.
Page 39 / 109
Section 3 – Configuration
D-Link DSL-2642B User Manual
38
Enable NAT:
Tick this option to enable NAT for this connection.
Enable Fullcone NAT:
he option appears when
Enable NAT
is
selected. Tick this option to enable Fullcone NAT for this connection.
Enable Firewall:
Tick this option to enable firewall for this connection.
Enable IGMP Multicast:
Tick this option to allow IGMP packets to go
through the WAN interface in both directions.
Selected WAN Interface:
Use the drop-down menu to choose the WAN
interface to use this connection.
Primary/Secondary DNS server:
Enter the Primary and Secondary
DNS Server IP addresses for this connection.
Click the
Apply
button to accept these changes.
Click the
Cancel
button to discard these changes.
Page 40 / 109
Section 3 – Configuration
D-Link DSL-2642B User Manual
39
There are 5 different variations in the
Service Category
drop-down menu when configuring the abovementioned connections.
UBR Without PCR
There is no additional field listed when choosing this category.
UBR With PCR
Peak Cell Rate:
Here the user can enter the Peak Cell Rate used.
CBR
Peak Cell Rate:
Here the user can enter the Peak Cell Rate used.
Non Realtime VBR
Peak Cell Rate:
Here the user can enter the Peak Cell Rate used.
Sustainable Cell Rate:
Here the user can enter the Sustainable Cell
Rate used.
Maximum Burst Size:
Here the user can enter the Maximum Burst Size
used.
Realtime VBR
Peak Cell Rate:
Here the user can enter the Peak Cell Rate used.
Sustainable Cell Rate:
Here the user can enter the Sustainable Cell
Rate used.
Maximum Burst Size:
Here the user can enter the Maximum Burst Size
used.
19216811.live