Page 66 / 69 Scroll up to view Page 61 - 65
Appendix B - Networking Basics
D-Link DSL-2540U User Manual
66
Networking Basics
Check Your IP Address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless
router) automatically. To verify your IP address, please follow the steps below.
Click on
Start
>
Run
. In the run box type
cmd
and click on the
OK
.
At the prompt, type
ipconfig
and press
Enter
.
This will display the IP address, subnet mask, and the default
gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation, security
settings, and the settings on your router. Some firewall software
programs may block a DHCP request on newly installed adapters.
If you are connecting to a wireless network at a hotspot (e.g. hotel,
coffee shop, airport), please contact an employee or administrator
to verify their wireless network settings.
Page 67 / 69
Appendix B - Networking Basics
D-Link DSL-2540U User Manual
67
Statically Assign an IP Address
If your DHCP is disabled, or you need to assign a static IP address, please follow the steps below:
Step 1
Windows® XP - Click on
Start
>
Control Panel
>
Network Connections
.
Windows® 2000 - From the desktop, right-click on the
My Network Places
>
Properties
.
Step 2
Right-click on the
Local Area Connection
which represents your D-Link network adapter and select
Properties
.
Step 3
Highlight
Internet Protocol (TCP/IP)
and click on the
Properties
.
Step 4
Click on the
Use the following IP address
and enter an IP address that is on the same subnet as
your network or the LAN IP address on your router.
Example: If the router’s LAN IP address is 192.168.1.1, make your IP address 192.168.1.X where X
is a number between 2 and 99. Make sure that the number you choose is not in use on the network.
Set Default Gateway the same as the LAN IP address of your router (192.168.1.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.1.1). The Secondary
DNS is not needed or you may enter a DNS server from your ISP.
Step 5
Click on the
OK
twice to save your settings.
Page 68 / 69
Appendix B - Networking Basics
D-Link DSL-2540U User Manual
Technical Specification
ADSL Standards
ANSI T1.413 Issue 2
ITU G.992.1 (G.dmt) AnnexA
ITU G.992.2 (G.lite) Annex A
ITU G.994.1 (G.hs)
ADSL2 Standards
ITU G.992.3 (G.dmt.bis) Annex A
ADSL2+ Standards
ITU G.992.5 Annex A
Protocols
IEEE 802.1d Spanning
Tree
TCP/UDP
ARP
RARP
ICMP
RFC1058 RIP v1
RFC1213 SNMP v1 & v2c
RFC1334 PAP
RFC1389 RIP v2
RFC1577 Classical IP over
ATM
RFC1483/2684
Multiprotocol
Encapsulation over ATM
Adaptation Layer 5 (AAL5)
RFC1661 Point to Point
Protocol
RFC1994 CHAP
RFC2131 DHCP Client /
DHCP Server
RFC2364 PPP over ATM
RFC2516 PPP over
Ethernet
Page 69 / 69
Appendix B - Networking Basics
D-Link DSL-2540U User Manual
Data Transfer Rate
G.dmt full rate downstream: up to 8 Mbps / upstream: up to 1 Mbps
G.lite: ADSL downstream up to 1.5 Mbps / upstream up to 512 Kbps
G.dmt.bis full rate downstream: up to 12 Mbps / upstream: up to 1 Mbps
ADSL full rate downstream: up to 24 Mbps / upstream: up to 1 Mbps
Media Interface
ADSL interface: RJ-11 connector for connection to 24/26 AWG twisted pair telephone line
LAN interface: RJ-45 port for 10/100BASE-T Ethernet connection
Certification:
This device complies with Part15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top