D-Link DSL-2320B Router Manual PDF (Setup & Configuration Guide)

Page 11 / 64 Scroll up to view Page 6 - 10

11

D-Link DSL-±3±0B ADSL±+ Ethernet/USB Modem User Manual

Section 5 - USB Installation

The next screen allows you to select how you want the wizard

to ﬁnd the driver on your computer. The default selection is set

to search for a suitable driver for my device (recommended).

To contunue, click

Next, you can specify the search locations. Make sure

CD-ROM drives

and

Specify a Location

are selected

and click

Page 12 / 64

1±

D-Link DSL-±3±0B ADSL±+ Ethernet/USB Modem User Manual

Section 5 - USB Installation

At this point, you can insert the CD-ROM into your

computer’s CD-ROM drive and click on the

Browse

button

to specify the CD-ROM drive of your computer.

To driver is located in the folder named

Bcm63xx_WHQL_

usb_driver

.

The ﬁle name is

usbdslur.inf

. Click

Open

to

proceed with the installation.

After the ﬁle has been selected, the this screen will appear

verifying the location where the ﬁle will be extracted from.

Click on

OK

to continue.

Page 13 / 64

13

D-Link DSL-±3±0B ADSL±+ Ethernet/USB Modem User Manual

Section 5 - USB Installation

This next screen shows the device and the driver to be

installed. Click

The last screen conﬁrms that the installation is complete.

Click on

Finish

to close the wizard.

Page 14 / 64

14

D-Link DSL-±3±0B ADSL±+ Ethernet/USB Modem User Manual

Section 4 - Conﬁguring Your Computer

Prior to accessing the modem through the LAN or USB port, note the following necessary conﬁgurations:

• Your PC’s TCP/IP address:

19±.168.1.x (where “x” is any number between ± and ±54)

• The modem’s default IP address: 19±.168.1.1

• Subnet mask: ±55.±55.±55.0

Below are the procedures for conﬁguring your computer. Follow the instructions for the operating system that you are

using.

Conﬁguring Your Computer

Windows

®

2000

These are instructions for conﬁguring your Windows

®

±000 operating system. If you are using Windows

®

XP please

proceed to page 15.

1.

In the Windows taskbar, click on the

Start

button and point to

Settings > Control Panel > Network and

Dial-up Connections

(in that order).

±.

Click on

Local Area Connection

.

When you have the Local Area Connection Status window open, click

on

Properties

.

3.

Listed in the window are the installed network components.

If the list includes Internet Protocol (TCP/IP),

then the protocol has already been enabled, and you can skip to Step 10.

4.

If Internet Protocol (TCP/IP) does not appear as an installed component, then click on

Install

.

5.

In the Select Network Component Type window, click on

protocol

and then the

Add

button.

6. Select

Internet Protocol (TCP/IP)

from the list and then click on

OK

.

Page 15 / 64

15

D-Link DSL-±3±0B ADSL±+ Ethernet/USB Modem User Manual

Section 4 - Conﬁguring Your Computer

7.

If prompted to restart your computer with the new settings, click

OK

.

8.

After your computer restarts, click on the

Network and Dial-up Connections

icon again, and right click

on the

Local Area Connection

icon and then select

Properties

.

9.

In the Local Area Connection Properties dialog box, select

Internet Protocol (TCP/IP)

and then click on

Properties

.

10. In the Internet Protocol (TCP/IP) Properties dialog box, click in the radio button labeled

Use the following

IP address

and type 19±.168.1.x (where “x” is any number between ± and ±54) and ±55.±55.±55.0 in

the IP address ﬁeld and Subnet Mask ﬁeld.

Windows

®

XP

1. In the Windows taskbar, click on the

Start

button then go to

Control Panel

and then click

Network

Connections

.

±. In the

Network Connections

window, right click on the

Local Area Connection

icon and click on

Properties

.

3. Listed in the

Local Area Connection

window are the installed network components.

Make sure the box

for Internet Protocol (TCP/IP) is checked and then click on

Properties

.

4.

In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio button labeled

Use the following

IP address

and type 19±.168.1.x (where x is any number between ± and ±54) for the IP address ﬁeld

and ±55.±55.±55.0 for the Subnet Mask ﬁeld.

5. Click on

OK

twice to save your changes and then close the Control Panel.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share