Page 46 / 181
Scroll up to view Page 41 - 45
41
D-Link DIR-890L User Manual
Section 3 - Configuration
Enter the IPv6 address lifetime (in minutes).
Click
Save
when you are done.
Router
Advertisement
Lifetime:
Page 47 / 181
42
D-Link DIR-890L User Manual
Section 3 - Configuration
Auto Configuration
Select either
Obtain DNS server address
or
Use the following
DNS
.
If you selected
Use the following DNS address
above, enter the
Primary DNS Server
address.
If you selected
Use the following DNS address
above, enter the
Secondary DNS Server address.
Enable or disable prefix delegation services.
If you disabled DHCP-PD, enter the LAN (local) IPv6 address for
the router.
Displays the router’s
LAN Link-Local Address
.
Enable or disable the
Automatic IPv6 Address Assignment
feature.
Enable or disable
Automatic DHCP-PD in LAN
services.
Select
SLAAC + RDNSS
,
SLAAC + Stateless DHCP
, or
Stateful
DHCPv6
.
Enter the IPv6 address lifetime (in minutes).
Click
Save
when you are done.
DNS Type:
Primary DNS
Server:
Secondary DNS
Server:
Enable DHCP-PD:
LAN IPv6 Address:
LAN IPv6 Link-
Local Address:
Enable Automatic
IPv6 Address
Assignment:
Enable Automatic
DHCP-PD in LAN:
Autoconfiguration
Type:
Router
Advertisement
Lifetime:
Auto Configuration is a connection method where the ISP assigns your IPv6 address when your router requests one from the ISP’s server. Some
ISPs require you to change some settings on your side before your router can connect to the IPv6 Internet.
Page 48 / 181
43
D-Link DIR-890L User Manual
Section 3 - Configuration
PPPoE
Choose
Share with IPv4
to re-use your IPv4 PPPoE username and
password, or
Create a new session
.
If you selected
Create a new session
above, enter the PPPoE
Username
provided by your ISP.
If you selected
Create a new session
above, enter the PPPoE
Password
provided by your ISP.
Select
Static IP
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select
Dynamic IP
.
Enter the
IP Address
provided by your ISP (for Static IP only).
If you selected
Create a new session
above, enter the ISP
Service
Name
(optional).
If you selected
Create a new session
above, select either
Always
on
,
On demand
, or
Manual
.
Maximum Transmission Unit - you may need to change the MTU for
optimal performance with your ISP.
Select either
Obtain DNS server address
or
Use the following DNS
.
If you selected
Use the following DNS
, enter the
Primary DNS
Server
address.
If you selected
Use the following DNS
, enter the
Secondary DNS
Server
address.
PPPoE Session:
Username:
Password:
Address Mode:
IP Address:
Service Name:
Reconnect
Mode:
MTU:
DNS Type:
Primary DNS
Server:
Secondary DNS
Server:
Select
PPPoE
(Point-to-Point-Tunneling Protocol) if your Internet connection requires you to enter a username and password. This information can
be provided by your Internet service provider (ISP). Required fields will vary, depending on the options you have enabled.*
Note
:
When you select
Share with IPv4
and
Dynamic IP
instead of
Create a new session
and
Static IP,
less fields are required. See screen shot on the next page.
Page 49 / 181
44
D-Link DIR-890L User Manual
Section 3 - Configuration
Enable or disable prefix delegation services.
Enter the LAN (local) IPv6 address for the router.
Displays the router’s
LAN IPv6 Link-Local Address
.
Enable or disable the
Automatic IPv6 Address Assignment
feature.
Select
SLAAC + RDNSS
,
SLAAC + Stateless DHCP
or
Stateful
DHCPv6
.
Enter the IPv6 address lifetime (in minutes).
Click
Save
when you are done.
Enable DHCP-
PD:
LAN IPv6
Address:
LAN IPv6 Link-
Local Address:
Enable
Automatic
IPv6 Address
Assignment:
Auto
Configuration
Type:
Router
Advertisement
Lifetime:
Page 50 / 181
45
D-Link DIR-890L User Manual
Section 3 - Configuration
IPv6 in IPv4 Tunnel
Enter the
Remote IPv4
address you will use.
Enter the
Remote IPv6
address you will use.
Displays the
Local IPv4
address.
Enter the
Local IPv6
address you will use.
Enter the
Subnet Prefix Length
supplied by your ISP.
Select either
Obtain DNS server address
or
Use the following DNS
.
If you selected
Use the following DNS
above, enter the
Primary
DNS Server
address.
If you selected
Use the following DNS
above, enter the
Secondary
DNS Server
address.
Enable or disable prefix delegation services.
If you disabled DHCP-PD, enter the LAN (local) IPv6 address for the
router.
Displays the router’s
LAN IPv6 Link-Local Address
.
Remote IPv4
Address:
Remote IPv6
Address:
Local IPv4
Address:
Local IPv6
Address:
Subnet Prefix
Length:
DNS Type:
Primary DNS
Server:
Secondary DNS
Server:
Enable DHCP-
PD:
LAN IPv6
Address:
LAN IPv6 Link-
Local Address:
You can configure the IPv6 connection to run in IPv4 Tunnel mode. IPv6 over IPv4 tunneling encapsulates IPv6 packets in IPv4 packets so that IPv6
packets can be sent over an IPv4 infrastructure.
19216811.live