Page 31 / 215
Scroll up to view Page 26 - 30
26
D-Link DIR-866L User Manual
Section 3 - Configuration
Select
PPPoE (Username/Password)
from the drop-down menu.
Check the box to
Enable True Gigabit Routing Connectivity.
In most cases, select
Dynamic IP
. Select
Static IP
if your ISP assigned
you the IP address, subnet mask, gateway, and DNS server addresses.
Enter the
IP Address
(Static PPPoE only).
Enter your PPPoE
Username
.
Enter your PPPoE
Password
and retype the password in the next box.
Enter the ISP
Service Name
(optional).
Select either
Always-on
,
On-Demand
, or
Manual
.
Enter a
Maximum Idle Time
during which the Internet connection is
maintained during inactivity. Enable Auto-reconnect to disable this
feature.
Enter the Primary and Secondary DNS Server Addresses of your choice
or enter DNS Server Addresses supplied by your ISP.
Maximum Transmission Unit - you may need to change the
MTU
for optimal performance with your specific ISP. 1492 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can click on
Clone Your PC’s MAC Address
to replace
the Internet port’s MAC address with the MAC address of your Ethernet card.
My Internet
Connection is:
True Gigabit Routing
Connectivity Setting:
Address Mode:
IP Address:
Username:
Password:
Service Name:
Reconnect Mode:
Maximum Idle Time:
DNS Server
Addresses:
MTU:
MAC Address:
Internet Setup
PPPoE (DSL)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP (Internet Service Provider) uses a PPPoE connection. Your ISP will provide you with a
username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software
is no longer needed and will not work through a router.
Page 32 / 215
27
D-Link DIR-866L User Manual
Section 3 - Configuration
Select
PPTP (Username/Password)
from the drop-down menu.
In most cases, select
Dynamic IP
. Select
Static IP
if your ISP assigned
you the IP address, subnet mask, gateway, and DNS server addresses.
Enter the
IP Address
(Static PPTP only).
Enter the
Subnet Mask
(Static PPTP only).
Enter the
Gateway IP Address
provided by your ISP.
Enter the
Server IP Address
provided by your ISP (optional).
Enter your PPTP
Username
.
Enter your PPTP
Password
and then retype the password in the next
box.
Select either
Always-on
,
On-Demand
, or
Manual
.
Enter a
Maximum Idle Time
during which the Internet connection is maintained during inactivity. Enable Auto-reconnect to disable this
feature.
Enter the Primary and Secondary DNS Server Addresses. The DNS server information will be supplied by your ISP.
Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol) if your ISP (Internet Service Provider) uses a PPTP connection. Your ISP will provide you with a
username and password.
My Internet
Connection is:
Address Mode:
PPTP IP Address:
PPTP Subnet
Mask:
PPTP Gateway IP
Address:
PPTP Server IP
Address:
Username:
Password:
Reconnect Mode:
Maximum Idle
Time:
DNS Servers:
Page 33 / 215
28
D-Link DIR-866L User Manual
Section 3 - Configuration
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can click on
Clone Your PC’s MAC Address
to replace
the Internet port’s MAC address with the MAC address of your Ethernet card.
MTU:
MAC Address:
Page 34 / 215
29
D-Link DIR-866L User Manual
Section 3 - Configuration
Select
L2TP (Username/Password)
from the drop-down menu.
In most cases, select
Dynamic IP
. Select
Static IP
if your ISP assigned
you the IP address, subnet mask, gateway, and DNS server addresses.
Enter the
L2TP IP Address
supplied by your ISP (Static only).
Enter the
Subnet Mask
supplied by your ISP (Static only).
Enter the
Gateway IP Address
provided by your ISP.
Enter the
Server IP Address
provided by your ISP (optional).
Enter your L2TP
Username
.
Enter your L2TP
Password
and then retype the password in the
next box.
Select either
Always-on
,
On-Demand
, or
Manual
.
Enter a
Maximum Idle Time
during which the Internet connection is maintained during inactivity. To disable this feature,
enable Auto-reconnect.
Enter the Primary and Secondary DNS Server Addresses (Static L2TP only).
My Internet
Connection is:
Address Mode:
L2TP IP Address:
L2TP Subnet
Mask:
L2TP Gateway IP
Address:
L2TP Server IP
Address:
Username:
Password:
Reconnect Mode:
Maximum Idle
Time:
DNS Servers:
Internet Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP (Internet Service Provider) uses a L2TP connection. Your ISP will provide you with a username
and password.
Page 35 / 215
30
D-Link DIR-866L User Manual
Section 3 - Configuration
MTU:
MAC Address:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can click on
Clone Your PC’s MAC Address
to replace
the Internet port’s MAC address with the MAC address of your Ethernet card.
19216811.live