Page 36 / 173
Scroll up to view Page 31 - 35
31
D-Link DIR-860L User Manual
Section 3 - Configuration
Select
PPTP (Username/Password)
from the drop-down menu.
Select
Static
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select
Dynamic IP
.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses (Static PPTP
only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your PPTP username.
Enter your PPTP password and then retype the password in the next
box.
Select either
Always-on
,
On-Demand
, or
Manual
.
Enter a maximum idle time during which the Internet connection is
maintained during inactivity. To disable this feature, enable Auto-reconnect.
Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
My Internet
Connection is:
Address Mode:
PPTP IP Address:
PPTP Subnet
Mask:
PPTP Gateway IP
Address:
PPTP Server IP
Address:
Username:
Password:
Reconnect
Mode:
Maximum Idle
Time:
Page 37 / 173
32
D-Link DIR-860L User Manual
Section 3 - Configuration
The DNS server information will be supplied by your ISP (Internet Service Provider.)
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can use the
Clone Your PC’s MAC Address
button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
DNS Servers:
MTU:
MAC Address:
Page 38 / 173
33
D-Link DIR-860L User Manual
Section 3 - Configuration
Select
L2TP (Username/Password)
from the drop-down menu.
Select
Static IP
if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic IP
.
Enter the L2TP IP address supplied by your ISP (Static only).
Enter the Subnet Mask supplied by your ISP (Static only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your L2TP username.
Enter your L2TP password and then retype the password in
the next box.
Select either
Always-on
,
On-Demand
, or
Manual
.
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this feature,
enable Auto-reconnect.
My Internet
Connection is:
Address Mode:
L2TP IP Address:
L2TP Subnet
Mask:
L2TP Gateway IP
Address:
L2TP Server IP
Address:
Username:
Password:
Reconnect
Mode:
Maximum Idle
Time:
Internet Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and
password. This option is typically used for DSL services.
Page 39 / 173
34
D-Link DIR-860L User Manual
Section 3 - Configuration
DNS Servers:
MTU:
MAC Address:
Enter the Primary and Secondary DNS Server Addresses (Static L2TP only).
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can use the
Clone Your PC’s MAC Address
button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
Page 40 / 173
35
D-Link DIR-860L User Manual
Section 3 - Configuration
Internet Setup
DS-Lite
My Internet
Connection is:
DS-Lite
Configuration:
Select
DS-Lite
from the drop-down menu.
Select the
DS-Lite DHCPv6 Option
to let the router allocate
the AFTR IPv6 address automatically. Select the
Manual
Configuration
option to enter the AFTR IPv6 address in
manually.
AFTR IPv6
Address:
After selecting the
Manual Configuration
option above,
enter the AFTR IPv6 address used here.
B4 IPv4 Address:
Enter the B4 IPv4 address value used here. (Optional.)
WAN IPv6
Address:
Once connected, the WAN IPv6 address will be displayed here.
IPv6 WAN
Default Gateway
Once connected, the IPv6 WAN Default Gateway address will
be displayed here.
DS-Lite is an IPv6 connection type. After selecting DS-Lite, the following parameters will be available for configuration:
19216811.live