Enter your L2TP password and then retype the password in the next box.
Select either
Always-on
,
On-Demand
, or
Manual
.
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
Enter the Primary and Secondary DNS Server Addresses (Static L2TP only).
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can use the
Clone.Your.PC’s.MAC.Address
button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
Page 42 / 161
37
D-Link DIR-826L User Manual
Section 3 - Configuration
Internet Setup
DS-Lite
Another Internet Connection type is DS-Lite.
DS-Lite
Configuration:
Select the DS-Lite DHCPv6 option to let the router allocate the
AFTR IPv6 address automatically. Select the Manual Configuration
to enter the AFTR IPv6 address in manually.
AFTR IPv6
Address:
After selecting the Manual Configuration option above, enter the
AFTR IPv6 address used here.
B4 IPv4 Address:
Enter the B4 IPv4 address value used here.
WAN IPv6
Address:
Once connected, the WAN IPv6 address will be displayed here.
IPv6 WAN
Default Gateway
Once connected, the IPv6 WAN Default Gateway address will be
displayed here.
DS-Lite is an IPv6 connection type. After selecting DS-Lite, the following parameters will be available for configuration:
Page 43 / 161
38
D-Link DIR-826L User Manual
Section 3 - Configuration
Wireless Settings
If you want to configure the wireless settings on your router using
the wizard, click
Wireless.Security.Setup.Wizard.
and refer to
page 42.
Click
Add.Wireless.Device.with.WPS
if you want to add a wireless
device using Wi-Fi Protected Setup (WPS) and refer to page 44.
If you want to manually configure the wireless settings on your
router click
Manual
Wireless.Network.Setup.
and refer to the
next page.
Page 44 / 161
39
D-Link DIR-826L User Manual
Section 3 - Configuration
Check the box to enable the wireless function. If you do not want to use
wireless, uncheck the box to disable all the wireless functions.
Select the time frame that you would like your wireless network enabled.
The schedule may be set to
Always
. Any schedule you create will be
available in the drop-down menu. Click
New.Schedule
to create a
schedule.
Service Set Identifier (SSID) is the name of your wireless network. Create
a name for your wireless network using up to 32 characters. The SSID is
case-sensitive.
Select one of the following:
802±11b.Only
- Select only if all of your wireless clients are 802.11b.
802±11g.Only
- Select only if all of your wireless clients are 802.11g.
802±11n.Only
- Select only if all of your wireless clients are 802.11n.
Mixed.802±11g.and.802±11b
- Select if you are using both 802.11g and 802.11b wireless clients.
Mixed.802±11n.and.802±11g
- Select if you are using both 802.11n and 802.11g wireless clients.
Mixed.802±11n,.11g,.and.11b
- Select if you are using a mix of 802.11n, 802.11g, and 802.11b wireless clients.
The
Auto.Channel.Scan
setting can be selected to allow the DIR-826L to choose the channel with the least amount of interference.
Indicates the channel setting for the DIR-826L. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless
network or to customize the wireless network. If you enable
Auto.Channel.Scan
, this option will be greyed out.
Select the Channel Width:
Auto.20/40
- This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices.
20MHz
- Select if you are not using any 802.11n wireless clients.
Select
Invisible
if you do not want the SSID of your wireless network to be broadcasted by the DIR-826L. If Invisible is selected, the SSID of the DIR-826L will
not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-826L in order to connect to it.
Refer to page 41 for more information regarding wireless security.
Enable Wireless:
Schedule:
Wireless Network
Name:
802.11 Mode:
Enable Auto Channel
Scan:
Wireless Channel:
Manual Wireless Settings
Channel Width:
Visibility Status:
Wireless Security:
802.11n/g (2.4GHz)
Page 45 / 161
40
D-Link DIR-826L User Manual
Section 3 - Configuration
802.11n/a (5GHz)
Check the box to enable the wireless function. If you do not want to
use wireless, uncheck the box to disable all the wireless functions.
Select the time frame that you would like your wireless network
enabled. The schedule may be set to
Always
. Any schedule you
create will be available in the drop-down menu. Click
New.Schedule
to create a schedule.
Service Set Identifier (SSID) is the name of your wireless network.
Create a name for your wireless network using up to 32 characters.
The SSID is case-sensitive.
Select one of the following:
802±11a.Only
- Select if all of your wireless clients are 802.11a.
802±11n.Only
- Select only if all of your wireless clients are 802.11n.
Mixed.802±11n.and.802±11a
- Select if you are using both 802.11n and 802.11a wireless clients.
The
Auto.Channel.Scan
setting can be selected to allow the DIR-826L to choose the channel with the least amount of interference.
Indicates the channel setting for the DIR-826L. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless
network or to customize the wireless network. If you enable
Auto.Channel.Scan
, this option will be greyed out.
Select the Channel Width:
Auto.20/40
- This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices.
20MHz
- Select if you are not using any 802.11n wireless clients.
Select
Invisible
if you do not want the SSID of your wireless network to be broadcasted by the DIR-826L. If Invisible is selected, the SSID of the DIR-826L will
not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-826L in order to connect to it.
Refer to the next page for more information regarding wireless security.
19216811.live