56

D-Link DIR-825 User Manual

Section 3 - Configuration

Static.IPv6.Address.Connection

This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your

IPv6 configuration settings. You must enter the IPv6 address, Subnet Prefix Length, Default Gateway, Primary DNS Server, and Secondary DNS

Server. Your ISP provides you with all this information.

Use.Link-Local.

Address:

IPv6.Address:

Subnet.Prefix.

Length:

Default.Gateway:

Primary.IPv6.DNS.

Address:

Secondary.IPv6.

DNS.Address:

LAN.IPv6.Address:

The Link-local address is used by nodes and routers when

communicating with neighboring nodes on the same link.

This mode enables IPv6-capable devices to communicate

with each other on the LAN side.

Enter the WAN IPv6 address for the router here.

Enter the WAN subnet prefix length value used here.

Enter the WAN default gateway IPv6 address used here.

Enter the WAN primary DNS Server address used here.

Enter the WAN secondary DNS Server address used here.

These are the settings of the LAN (Local Area Network)

IPv6 interface for the router. The router’s LAN IPv6 Address

configuration is based on the IPv6 Address and Subnet

assigned by your ISP. (A subnet with prefix /64 is supported

in LAN.)

57

D-Link DIR-825 User Manual

Section 3 - Configuration

The following parameters will be available for configuration:

6rd IPv6 Prefix:

Enter the 6rd IPv6 address and prefix value used

here.

IPv4 Address:

Enter the IPv4 address used here.

Mask Length:

Enter the IPv4 mask length used here.

Assigned IPv6 Prefix:

Displays the IPv6 assigned prefix value here.

6rd Border Relay IPv4

Address:

Enter the 6rd border relay IPv4 address used here.

IPv6 DNS Server:

Enter the primary DNS Server address used here.

The IPv6 Internet Connection Setup Wizard is complete.

Click on the

Connect

button to continue. Click on the

Prev

button to return to

the previous page. Click on the

Cancel

button to discard all the changes made

and return to the main page.

Tunneling.Connection.(6rd)

After selecting the Tunneling Connection (6rd) option, the user can configure the IPv6 6rd connection settings.

58

D-Link DIR-825 User Manual

Section 3 - Configuration

IPv6 Manual Setup

There are several connection types to choose from: Auto Detection, Static IPv6, Autoconfiguration (SLAAC/DHCPv6), PPPoE,

IPv6 in IPv4 Tunnel, 6to4, 6rd, and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet

Service Provider.

Note:

If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed

or disabled.

Auto Detection

Select

Auto.Detection

to have the router detect and automatically

configure your IPv6 setting from your ISP.

59

D-Link DIR-825 User Manual

Section 3 - Configuration

Static IPv6

Select

Static.IPv6

from the drop-down menu.

Enter the address settings supplied by your Internet provider

(ISP).

Enter the LAN (local) IPv6 address for the router.

Displays the Router’s LAN Link-Local Address.

Check to enable the Autoconfiguration feature.

Select

Stateful.(DHCPv6)

,

SLAAC.+.RDNSS

or

SLAAC.+.

Stateless.DHCPv6

.

Enter the start IPv6 Address for the DHCPv6 range for your

local computers.

Enter the end IPv6 Address for the DHCPv6 range for your

local computers.

Enter the IPv6 Address Lifetime (in minutes).

My IPv6 Connection:

WAN IPv6 Address

Settings:

LAN IPv6 Address:

LAN Link-Local Address:

Enable

Autoconfiguration:

Autoconfiguration Type:

IPv6 Address Range

Start:

IPv6 Address Range

End:

IPv6 Address Lifetime:

60

D-Link DIR-825 User Manual

Section 3 - Configuration

Autoconfiguration

Select

Autoconfiguration.(Stateless/DHCPv6)

from the

drop-down menu.

Select either

Obtain.DNS.server.address.automatically

or

Use.the.following.DNS.Address

.

Enter the primary and secondary DNS server addresses.

Enter the LAN (local) IPv6 address for the router.

Displays the Router’s LAN Link-Local Address.

Check to enable the Autoconfiguration feature.

Select

Stateful.(DHCPv6)

,

SLAAC.+.RDNSS

or

SLAAC.+.

Stateless.DHCPv6

.

Enter the start IPv6 Address for the DHCPv6 range for your

local computers.

Enter the end IPv6 Address for the DHCPv6 range for your

local computers.

Enter the IPv6 Address Lifetime (in minutes).

My IPv6 Connection:

IPv6 DNS Settings:

Primary/Secondary DNS

Address:

LAN IPv6 Address:

LAN Link-Local Address:

Enable

Autoconfiguration:

Autoconfiguration Type:

IPv6 Address Range

Start:

IPv6 Address Range

End:

IPv6 Address Lifetime: