Page 61 / 158
Scroll up to view Page 56 - 60
56
D-Link DIR-825 User Manual
Section 3 - Configuration
Static.IPv6.Address.Connection
This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your
IPv6 configuration settings. You must enter the IPv6 address, Subnet Prefix Length, Default Gateway, Primary DNS Server, and Secondary DNS
Server. Your ISP provides you with all this information.
Use.Link-Local.
Address:
IPv6.Address:
Subnet.Prefix.
Length:
Default.Gateway:
Primary.IPv6.DNS.
Address:
Secondary.IPv6.
DNS.Address:
LAN.IPv6.Address:
The Link-local address is used by nodes and routers when
communicating with neighboring nodes on the same link.
This mode enables IPv6-capable devices to communicate
with each other on the LAN side.
Enter the WAN IPv6 address for the router here.
Enter the WAN subnet prefix length value used here.
Enter the WAN default gateway IPv6 address used here.
Enter the WAN primary DNS Server address used here.
Enter the WAN secondary DNS Server address used here.
These are the settings of the LAN (Local Area Network)
IPv6 interface for the router. The router’s LAN IPv6 Address
configuration is based on the IPv6 Address and Subnet
assigned by your ISP. (A subnet with prefix /64 is supported
in LAN.)
Page 62 / 158
57
D-Link DIR-825 User Manual
Section 3 - Configuration
The following parameters will be available for configuration:
6rd IPv6 Prefix:
Enter the 6rd IPv6 address and prefix value used
here.
IPv4 Address:
Enter the IPv4 address used here.
Mask Length:
Enter the IPv4 mask length used here.
Assigned IPv6 Prefix:
Displays the IPv6 assigned prefix value here.
6rd Border Relay IPv4
Address:
Enter the 6rd border relay IPv4 address used here.
IPv6 DNS Server:
Enter the primary DNS Server address used here.
The IPv6 Internet Connection Setup Wizard is complete.
Click on the
Connect
button to continue. Click on the
Prev
button to return to
the previous page. Click on the
Cancel
button to discard all the changes made
and return to the main page.
Tunneling.Connection.(6rd)
After selecting the Tunneling Connection (6rd) option, the user can configure the IPv6 6rd connection settings.
Page 63 / 158
58
D-Link DIR-825 User Manual
Section 3 - Configuration
IPv6 Manual Setup
There are several connection types to choose from: Auto Detection, Static IPv6, Autoconfiguration (SLAAC/DHCPv6), PPPoE,
IPv6 in IPv4 Tunnel, 6to4, 6rd, and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet
Service Provider.
Note:
If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed
or disabled.
Auto Detection
Select
Auto.Detection
to have the router detect and automatically
configure your IPv6 setting from your ISP.
Page 64 / 158
59
D-Link DIR-825 User Manual
Section 3 - Configuration
Static IPv6
Select
Static.IPv6
from the drop-down menu.
Enter the address settings supplied by your Internet provider
(ISP).
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select
Stateful.(DHCPv6)
,
SLAAC.+.RDNSS
or
SLAAC.+.
Stateless.DHCPv6
.
Enter the start IPv6 Address for the DHCPv6 range for your
local computers.
Enter the end IPv6 Address for the DHCPv6 range for your
local computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
WAN IPv6 Address
Settings:
LAN IPv6 Address:
LAN Link-Local Address:
Enable
Autoconfiguration:
Autoconfiguration Type:
IPv6 Address Range
Start:
IPv6 Address Range
End:
IPv6 Address Lifetime:
Page 65 / 158
60
D-Link DIR-825 User Manual
Section 3 - Configuration
Autoconfiguration
Select
Autoconfiguration.(Stateless/DHCPv6)
from the
drop-down menu.
Select either
Obtain.DNS.server.address.automatically
or
Use.the.following.DNS.Address
.
Enter the primary and secondary DNS server addresses.
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select
Stateful.(DHCPv6)
,
SLAAC.+.RDNSS
or
SLAAC.+.
Stateless.DHCPv6
.
Enter the start IPv6 Address for the DHCPv6 range for your
local computers.
Enter the end IPv6 Address for the DHCPv6 range for your
local computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
IPv6 DNS Settings:
Primary/Secondary DNS
Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable
Autoconfiguration:
Autoconfiguration Type:
IPv6 Address Range
Start:
IPv6 Address Range
End:
IPv6 Address Lifetime:
19216811.live