Page 76 / 136
Scroll up to view Page 71 - 75
71
D-Link DIR-815 User Manual
Section 3 - Configuration
IPv6
6to4
Select
6to4
from the
My IPv6 Connection is
drop-down menu if your Router will use an IPv6 to IPv4 tunnel to connect to the
Internet.
Enter the address settings supplied by your Internet
provider (ISP).
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Use this section to configure the IPv6 autoconfiguration
settings.
WAN IPv6 Address
Settings:
LAN IPv6 Address:
LAN IPv6
Link-Local Address:
LAN Address
Autoconfiguration
Settings:
Click the
Save Settings
button to save any changes made.
Page 77 / 136
72
D-Link DIR-815 User Manual
Section 3 - Configuration
IPv6
6to4- Stateless Autoconfiguration
To configure the Router to use an IPv6 to IPv4 tunnel stateless autoconfiguration connection, configure the parameters in the
LAN Address Autoconfiguration Settings
section as described below:
Check to enable the Autoconfiguration feature.
Select the
Stateless
option from the drop-down menu.
Enter the Router Advertisement Lifetime (in minutes).
Enable
Autoconfiguration:
Autoconfiguration
Type:
Router
Advertisement
Lifetime:
Click the
Save Settings
button to save any changes made.
Page 78 / 136
73
D-Link DIR-815 User Manual
Section 3 - Configuration
IPv6
6to4- Stateful (DHCPv6) Autoconfiguration
To configure the Router to use an IPv6 to IPv4 tunnel stateful autoconfiguration connection, configure the parameters in the
LAN Address Autoconfiguration Settings
section as described below:
Check to enable the Autoconfiguration feature.
Select the
Stateful(DHCPv6)
option from the drop-down
menu.
Enter the start IPv6 Address for the DHCPv6 range for your
local computers.
Enter the end IPv6 Address for the DHCPv6 range for your
local computers.
Enter the IPv6 Address Lifetime (in minutes).
Enable
Autoconfiguration:
Autoconfiguration
Type:
IPv6 Address Range
Start:
IPv6 Address Range
End:
IPv6 Address
Lifetime:
Click the
Save Settings
button to save any changes made.
Page 79 / 136
74
D-Link DIR-815 User Manual
Section 3 - Configuration
Displays the LAN IPv6 Link-Local address of the router.
LAN IPv6
Address
Settings:
IPv6
Link-local Only
Select
Link-local Only
from the
My IPv6 Connection is
drop-down menu if your Router will use the IPv6 link local method
to connect to the Internet.
Click the
Save Settings
button to save any changes made.
Page 80 / 136
75
D-Link DIR-815 User Manual
Section 3 - Configuration
IPv6 Firewall
The DIR-815’s IPv6 Firewall feature allows you to configure which kind of IPv6 traffic is allowed to pass through the device. The
DIR-815’s IPv6 Firewall functions in a similar way to the IP Filters feature.
Check the box on the left side to enable the IPv6 firewall
rule.
Enter a name to identify the IPv6 firewall rule.
Use the radio buttons to
Allow
or
Deny
transport of the
IPv6 data packets according to the criteria defined in the
firewall rule.
Use the
Source
drop-down menu to specify the interface
that connects to the source IPv6 addresses of the firewall
rule.
Enter the source IPv6 address range in the adjacent
IP
Address Range
field.
Use the
Dest
drop-down menu to specify the interface
that connects to the destination IP addresses of the
firewall rule.
Enter the destination IPv6 address range in the adjacent
IP Address Range
field.
Enable Checkbox:
Name:
Action:
Source:
Dest:
Use the drop-down menu to select the time schedule that the IPv6 Firewall Rule will be enabled on. The schedule may be set to
Always, which will allow the particular service to always be enabled. You can create your own times in the
Tools
>
Schedules
section.
Select the protocol of the firewall port (All, TCP, UDP, or ICMP).
Enter the first port of the range that will be used for the firewall rule in the top port range field and enter the last port in the field
underneath.
Select Schedule:
Protocol:
Port Range:
Click the
Save Settings
button to save any changes made.
19216811.live