D-Link DIR-803 Router Manual PDF (Setup & Configuration Guide)

Page 71 / 139 Scroll up to view Page 66 - 70

67

D-Link DIR-803 User Manual

Section 3 - Conﬁguration

6rd

Select

6rd

from the drop-down menu.

Enter the address settings supplied by your Internet provider

(ISP).

Enter the LAN (local) IPv6 address for the router.

Displays the Router’s LAN Link-Local Address.

Check to enable the Autoconﬁguration feature.

Select

Stateful (DHCPv6), SLAAC+RDNSS or SLAAC + Stateless

DHCPv6.

Enter the Router Advertisement Lifetime (in minutes).

My IPv6 Connection:

6RD Settings:

LAN IPv6 Address:

LAN Link-Local Address:

Enable

Autoconﬁguration:

Autoconﬁguration Type:

Router Advertisement

Lifetime:

Page 72 / 139

68

D-Link DIR-803 User Manual

Section 3 - Conﬁguration

Select

Link-Local.Only

from the drop-down

menu.

Displays the IPv6 address of the router.

My IPv6 Connection:

LAN IPv6 Address

Settings:

Link-Local Connectivity

Page 73 / 139

69

D-Link DIR-803 User Manual

Section 3 - Conﬁguration

This will allow you to open a single port. If you would like to open a range of ports, refer to the next page.

Enter a name for the rule or select an application from

the drop-down menu. Select an application and click

<<

to populate the ﬁelds.

Enter the IP address of the computer on your local

network that you want to allow the incoming

service to. If your computer is receiving an IP address

automatically from the router (DHCP), you computer

will be listed in the “Computer Name” drop-down

menu. Select your computer and click

<<

.

Enter the port that you want to open next to Private

Port and Public Port. The private and public ports are

usually the same. The public port is the port seen from

the Internet side, and the private port is the port being

used by the application on the computer within your

local network.

Select

TCP

,

UDP

, or

Both.

from the drop-down menu.

The schedule of time when the Virtual Server Rule

will be enabled. The schedule may be set to Always,

which will allow the particular service to always be

enabled. You can create your own times in the

Tools

>

Schedules

section.

Select

Allow.All

(most common) or a created Inbound

ﬁlter. You may create your own inbound ﬁlters in the

Advanced.>.Inbound.Filter

page.

Name:

IP Address:

Private Port/

Public Port:

Protocol Type:

Schedule:

Inbound Filter:

Virtual Server

Advanced

Page 74 / 139

70

D-Link DIR-803 User Manual

Section 3 - Conﬁguration

This will allow you to open a single port or a range of ports.

Port Forwarding

Enter a name for the rule or select an application

from the drop-down menu. Select an application

and click

<<

to populate the ﬁelds.

Enter the IP address of the computer on your local

network that you want to allow the incoming service

to. If your computer is receiving an IP address

automatically from the router (DHCP), you computer

will be listed in the “Computer Name” drop-down

menu. Select your computer and click

<<

.

Enter the TCP and/or UDP port or ports that you

want to open. You can enter a single port or a range

of ports. Separate ports with a common.

Example: 24,1009,3000-4000

The schedule of time when the Virtual Server Rule

will be enabled. The schedule may be set to

Always

,

which will allow the particular service to always be

enabled. You can create your own times in the

Tools

>

Schedules

section.

Select

Allow. All

(most common) or a created

Inbound ﬁlter. You may create your own inbound

ﬁlters in the

Advanced.>.Inbound.Filter

page.

Name:

IP Address:

TCP/UDP:

Schedule:

Inbound Filter:

Page 75 / 139

71

D-Link DIR-803 User Manual

Section 3 - Conﬁguration

Enter a name for the rule. You may select a

pre-deﬁned application from the drop-down menu

and click

<<

.

This is the port used to trigger the application. It

can be either a single port or a range of ports.

Select the protocol of the trigger port (TCP, UDP,

or Both).

This is the port number on the Internet side that

will be used to access the application. You may

deﬁne a single port or a range of ports. You can

use a comma to add multiple ports or port ranges.

Select the protocol of the ﬁrewall port (TCP, UDP,

or Both).

The schedule of time when the Application Rule

will be enabled. The schedule may be set to Always,

which will allow the particular service to always

be enabled. You can create your own times in the

Tools

>

Schedules

section.

Name:

Trigger:

Traﬃc Type:

Firewall:

Traﬃc Type:

Schedule:

Application Rules

Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others.

These applications have diﬃculties working through NAT (Network Address Translation). Special Applications makes some of

these applications work with the DIR-803. If you need to run applications that require multiple connections, specify the port

normally associated with an application in the “Trigger Port” ﬁeld, select the protocol type as TCP or UDP, then enter the ﬁrewall

(public) ports associated with the trigger port to open them for inbound traﬃc.

The DIR-803 provides some predeﬁned applications in the table on the bottom of the web page. Select the application you

want to use and enable it.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share