D-Link DIR-660 Router Manual PDF (Setup & Configuration Guide)

Page 21 / 98 Scroll up to view Page 16 - 20

±1

D-Link DIR-660 User Manual

Section ² - Conﬁguration

Select

Static

if your ISP assigned you the IP address,

subnet mask, gateway, and DNS server addresses. In

most cases, select

Dynamic

.

Enter the L2TP IP address supplied by your ISP (Static

only).

Enter the Subnet Mask supplied by your ISP (Static

only).

Enter the Gateway IP Address provided by your ISP.

Enter the Server IP provided by your ISP (optional).

Enter your L2TP username.

Enter your L2TP password and then retype the password

in the next box.

Select either

Always-on

,

On-Demand

, or

Manual

.

Enter a maximum idle time during which the Internet

connection is maintained during inactivity. To disable this

feature, enable Auto-reconnect.

Enter the Primary and Secondary DNS Server Addresses

(Static L2TP only).

Address Mode:

L2TP IP Address:

L2TP Subnet Mask:

L2TP Gateway:

L2TP Server IP:

Username:

Password:

Reconnect Mode:

Maximum Idle Time:

DNS Servers:

Internet Setup

L2TP

Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username

and password. This option is typically used for DSL services.

Downloaded from

www.Manualslib.com

manuals search engine

Page 22 / 98

±±

D-Link DIR-660 User Manual

Section ² - Conﬁguration

MTU:

Clone MAC

Address:

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1464 is the

default MTU.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not

recommended that you change the default MAC address unless required by your ISP.

You can use the

Clone Your PC’s

MAC Address

button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

Downloaded from

www.Manualslib.com

manuals search engine

Page 23 / 98

±²

D-Link DIR-660 User Manual

Section ² - Conﬁguration

Enter the IP address assigned by your ISP.

Enter the Subnet Mask assigned by your ISP.

Enter the Gateway assigned by your ISP.

The DNS server information will be supplied by your

ISP (Internet Service Provider.)

Maximum Transmission Unit - you may need to

change the MTU for optimal performance with your

speciﬁc ISP. 1500 is the default MTU.

The default MAC Address is set to the Internet port’s

physical interface MAC address on the Broadband

Router. It is not recommended that you change the

default MAC address unless required by your ISP.

You can use the

Clone Your PC’s MAC Address

button to replace the Internet port’s MAC address

with the MAC address of your Ethernet card.

IP Address:

Subnet Mask:

Default Gateway:

DNS Servers:

MTU:

MAC Address:

Internet Setup

Static (assigned by ISP)

Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address,

subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the ﬁelds must be in the

appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.

Downloaded from

www.Manualslib.com

manuals search engine

Page 24 / 98

±³

D-Link DIR-660 User Manual

Section ² - Conﬁguration

Enter the IP address of the login server.

Enter your BigPond username.

Enter your BigPond password and then retype

the password in the next box.

The DNS server information will be supplied

by your ISP (Internet Service Provider.)

Maximum Transmission Unit - you may need to

change the MTU for optimal performance with

your speciﬁc ISP. 1500 is the default MTU.

The default MAC Address is set to the

Internet’s physical interface MAC address on

the Broadband Router. It is not recommended

that you change the default MAC address

unless required by your ISP.

You can use the

Clone Your PC’s MAC Address

button to

replace the Internet port’s MAC address with

the MAC address of your Ethernet card.

BigPond Server:

BigPond Username:

BigPond Password:

DNS Servers:

MTU:

MAC Address:

Internet Setup

Big Pond

Downloaded from

www.Manualslib.com

manuals search engine

Page 25 / 98

±´

D-Link DIR-660 User Manual

Section ² - Conﬁguration

Check the box to enable the wireless function.

If you do not want to use wireless, uncheck the

box to disable all the wireless functions.

Service Set Identiﬁer (SSID) is the name of your

wireless network. Create a name using up to 32

characters. The SSID is case-sensitive.

The

Auto Channel Scan

setting can be selected

to allow the DIR-660 to choose the channel with

the least amount of interference.

Indicates the channel setting for the DIR-660.

By default the channel is set to 6. The Channel

can be changed to ﬁt the channel setting for an

existing wireless network or to customize the

wireless network. If you enable

Auto Channel

Scan

, this option will be greyed out.

Select one of the following:

802.11g Only

- Select if all of your wireless

clients are 802.11g.

Mixed 802.11g and 802.11b

- Select if you

are using both 802.11b and 802.11g wireless

clients.

802.11b Only

- Select if all of your wireless

clients are 802.11b.

802.11n Only

- Select only if all of your wireless

clients are 802.11n.

Mixed 802.11n, 802.11b, and 802.11g

- Select if you are using a mix of 802.11n, 11g, and 11b wireless clients.

Mixed 802.11n and 802.11g

- Select if you are using a mix of 802.11n and 802.11g wireless clients.

Enable Wireless:

Enable Auto

Channel Scan:

Wireless Settings

Wireless Network

Name:

Wireless Channel:

802.11 Mode:

Downloaded from

www.Manualslib.com

manuals search engine

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share