16

D-Link DIR-635 User Manual

Section 3 - Configuration

Click

Next

to continue.

Create a new password and then click

Next

to continue.

Select your time zone from the drop-down menu and then click

Next

to continue.

Select the type of Internet connection you use and then click

Next

to continue.

1³

D-Link DIR-635 User Manual

Section 3 - Configuration

If you selected Dynamic, you may need to enter the MAC address of the

computer that was last connected directly to your modem. If you are currently

using that computer, click

Clone Your PC’s MAC Address

and then click

Next

to continue.

The Host Name is optional but may be required by some ISPs. The default

host name is the device name of the Router and may be changed.

If you selected PPPoE, enter your PPPoE username and password. Click

Next

to continue.

Select

Static

if your ISP assigned you the IP address, subnet mask, gateway,

and DNS server addresses.

Note:

Make sure to remove your PPPoE software from your computer. The

software is no longer needed and will not work through a router.

If you selected PPTP, enter your PPTP username and password. Click

Next

to continue.

1´

D-Link DIR-635 User Manual

Section 3 - Configuration

If you selected L2TP, enter your L2TP username and password. Click

Next

to continue.

If you selected Static, enter your network settings supplied by your Internet

provider. Click

Next

to continue.

Click

Connect

to save your settings. Once the router is finished rebooting,

click

Continue

. Please allow 1-2 minutes to connect.

Close your browser window and reopen it to test your Internet connection.

It may take a few tries to initially connect to the Internet.

1µ

D-Link DIR-635 User Manual

Section 3 - Configuration

Select

Dynamic IP (DHCP)

to obtain IP Address

information automatically from your ISP. Select

this option if your ISP does not give you any IP

numbers to use. This option is commonly used

for Cable modem services.

The Host Name is optional but may be required

by some ISPs.

Check the box if you are having problems

obtaining an IP address from your ISP.

Enter the Primary DNS server IP address

assigned by your ISP.

Maximum Transmission Unit - you may need to

change the MTU for optimal performance with

your specific ISP. 1500 is the default MTU.

The default MAC Address is set to the Internet

port’s physical interface MAC address on the

Broadband Router. It is not recommended that

you change the default MAC address unless

required by your ISP.

You can use the

Clone

Your PC’s MAC Address

button to replace

the Internet port’s MAC address with the MAC

address of your Ethernet card.

My Internet

Connection:

Host Name:

MAC Address:

Manual Configuration

Dynamic (Cable)

DNS Addresses:

MTU:

Use Unicasting:

±0

D-Link DIR-635 User Manual

Section 3 - Configuration

Select

PPPoE (Username/Password)

from the drop-down menu.

Select

Static

if your ISP assigned you the IP address, subnet mask,

gateway, and DNS server addresses. In most cases, select

Dynamic

.

Enter the IP address (Static PPPoE only).

Enter your PPPoE user name.

Enter your PPPoE password and then retype the password in the next

box.

Enter the ISP Service Name (optional).

Select either

Always-on

,

On-Demand

, or

Manual

.

Enter the Primary and Secondary DNS Server Addresses (Static PPPoE

only).

Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature,

enable Auto-reconnect.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is

the default MTU.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not

recommended that you change the default MAC address unless required by your ISP.

You can use the

Clone Your PC’s

MAC Address

button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

My Internet

Connection:

Address Mode:

IP Address:

User Name:

Password:

Service Name:

Reconnection Mode:

Maximum Idle Time:

DNS Addresses:

MTU:

MAC Address:

Internet Setup

PPPoE (DSL)

Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide

you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE

software from your computer. The software is no longer needed and will not work through a router.