D-Link DIR-625v3 Router Manual PDF (Setup & Configuration Guide)

Page 31 / 94 Scroll up to view Page 26 - 30

²1

D-Link DIR-6±5 User Manual

Section ² - Conﬁguration

This will allow you to open a single port. If you would like to open a range of ports, refer to page 35.

Enter a name for the rule or select an application

from the drop-down menu. Select an application

and click

<<

to populate the ﬁelds.

Enter the IP address of the computer on your

local network that you want to allow the incoming

service to. If your computer is receiving an IP

address automatically from the router (DHCP),

you computer will be listed in the “Computer

Name” drop-down menu. Select your computer

and click

<<

.

Enter the port that you want to open next to Private

Port and Public Port. The private and public ports

are usually the same. The public port is the port

seen from the Internet side, and the private port

is the port being used by the application on the

computer within your local network.

Select

TCP

,

UDP

, or

ANY

from the drop-down

menu.

Select

Allow All

(most common) or a created

Inbound ﬁlter. You may create your own inbound

ﬁlters in the

Advanced > Inbound Filter

page.

The schedule of time when the Virtual Server

Rule will be enabled. The schedule may be set to

Always, which will allow the particular service to

always be enabled. You can create your own times

in the

Tools

>

Schedules

section.

Name:

IP Address:

Private Port/

Public Port:

Protocol Type:

Inbound Filter:

Schedule:

Downloaded from

www.Manualslib.com

manuals search engine

Page 32 / 94

²±

D-Link DIR-6±5 User Manual

Section ² - Conﬁguration

This will allow you to open a single port or a range of ports.

Port Forwarding

Enter a name for the rule or select an application

from the drop-down menu. Select an application

and click

<<

to populate the ﬁelds.

Enter the IP address of the computer on your local

network that you want to allow the incoming service

to. If your computer is receiving an IP address

automatically from the router (DHCP), you computer

will be listed in the “Computer Name” drop-down

menu. Select your computer and click

<<

.

Enter the TCP and/or UDP port or ports that you

want to open. You can enter a single port or a range

of ports. Seperate ports with a common.

Example: 24,1009,3000-4000

Select

Allow All

(most common) or a created

Inbound ﬁlter. You may create your own inbound

ﬁlters in the

Advanced > Inbound Filter

page.

The schedule of time when the Virtual Server Rule

will be enabled. The schedule may be set to Always,

which will allow the particular service to always be

enabled. You can create your own times in the

Tools

>

Schedules

section.

Name:

IP Address:

TCP/UDP:

Inbound Filter:

Schedule:

Downloaded from

www.Manualslib.com

manuals search engine

Page 33 / 94

²²

D-Link DIR-6±5 User Manual

Section ² - Conﬁguration

Enter a name for the rule. You may select a

pre-deﬁned application from the drop-down

menu and click

<<

.

This is the port used to trigger the application. It

can be either a single port or a range of ports.

Select the protocol of the trigger port (TCP,

UDP, or ANY).

This is the port number on the Internet side

that will be used to access the application. You

may deﬁne a single port or a range of ports.

You can use a comma to add multiple ports or

port ranges.

Select the protocol of the ﬁrewall port (TCP,

UDP, or ANY).

The schedule of time when the Application Rule

will be enabled. The schedule may be set to

Always, which will allow the particular service

to always be enabled. You can create your own

times in the

Tools

>

Schedules

section.

Name:

Trigger:

Trafﬁc Type:

Firewall:

Trafﬁc Type:

Schedule:

Application Rules

Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and

others. These applications have difﬁculties working through NAT (Network Address Translation). Special Applications

makes some of these applications work with the DIR-625. If you need to run applications that require multiple connections,

specify the port normally associated with an application in the “Trigger Port” ﬁeld, select the protocol type as TCP or

UDP, then enter the ﬁrewall (public) ports associated with the trigger port to open them for inbound trafﬁc.

The DIR-625 provides some predeﬁned applications in the table on the bottom of the web page. Select the application

you want to use and enable it.

Downloaded from

www.Manualslib.com

manuals search engine

Page 34 / 94

²³

D-Link DIR-6±5 User Manual

Section ² - Conﬁguration

QoS Engine

This option is disabled by default. Enable this

option for better performance and experience with

online games and other interactive applications,

such as VoIP.

This option should be enabled when you have a

slow Internet uplink. It helps to reduce the impact

that large low priority network packets can have

on more urgent ones.

This option is enabled by default when the QoS

Engine option is enabled. This option will allow

your router to automatically determine the uplink

speed of your Internet connection.

This displays the detected uplink speed.

The speed at which data can be transferred from the router to your ISP. This is determined by your ISP. ISP’s often speed as

a download/upload pair. For example, 1.5Mbits/284Kbits. Using this example, you would enter 284. Alternatively you can test

your uplink speed with a service such as www.dslreports.com.

By default, the router automatically determines whether the underlying connection is an xDSL/Frame-relay network or some

other connection type (such as cable modem or Ethernet), and it displays the result as Detected xDSL or Frame Relay Network.

If you have an unusual network connection in which you are actually connected via xDSL but for which you conﬁgure either

“Static” or “DHCP” in the Internet settings, setting this option to xDSL or Other Frame Relay Network ensures that the router

will recognize that it needs to shape trafﬁc slightly differently in order to give the best performance. Choosing xDSL or Other

Frame Relay Network causes the measured uplink speed to be reported slightly lower than before on such connections, but

gives much better results.

When Connection Type is set to automatic, the automatically detected connection type is displayed here.

Enable

StreamEngine:

Dynamic

Fragmentation:

Automatic Uplink

Speed:

Measured Uplink

Speed:

Manual Uplink

Speed:

Connection Type:

Detected xDSL:

The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the

QoS Engine settings are disabled and application priority is not classiﬁed automatically.

Downloaded from

www.Manualslib.com

manuals search engine

Page 35 / 94

²5

D-Link DIR-6±5 User Manual

Section ² - Conﬁguration

Network Filters

Select Turn MAC Filtering Off, allow MAC

addresses listed below, or deny MAC addresses

listed below from the drop-down menu.

Enter the MAC address you would like to ﬁlter.

To ﬁnd the MAC address on a computer, please

refer to the Networking Basics section in this

manual.

Select a DHCP client from the drop-down menu

and click

<<

to copy that MAC Address.

Conﬁgure MAC

Filtering:

MAC Address:

DHCP Client:

Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses

from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of

clients that are currently connected to the Broadband Router.

Downloaded from

www.Manualslib.com

manuals search engine

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share