Page 16 / 94 Scroll up to view Page 11 - 15
16
D-Link DIR-6±5 User Manual
Section ² - Configuration
If you selected L2TP, enter your L2TP username and password. Click
Next
to continue.
If you selected Static, enter your network settings supplied by your Internet
provider. Click
Next
to continue.
Click
Connect
to save your settings. Once the router is finished rebooting,
click
Continue
. Please allow 1-2 minutes to connect.
Close your browser window and reopen it to test your Internet connection.
It may take a few tries to initially connect to the Internet.
Downloaded from
www.Manualslib.com
manuals search engine
Page 17 / 94
D-Link DIR-6±5 User Manual
Section ² - Configuration
Select
Dynamic IP (DHCP)
to obtain IP Address
information automatically from your ISP. Select
this option if your ISP does not give you any IP
numbers to use. This option is commonly used
for Cable modem services.
The Host Name is optional but may be required
by some ISPs.
Check the box if you are having problems
obtaining an IP address from your ISP.
Enter the Primary DNS server IP address
assigned by your ISP.
Maximum Transmission Unit - you may need to
change the MTU for optimal performance with
your specific ISP. 1500 is the default MTU.
The default MAC Address is set to the Internet
port’s physical interface MAC address on the
Broadband Router. It is not recommended that
you change the default MAC address unless
required by your ISP.
You can use the
Clone
Your PC’s MAC Address
button to replace
the Internet port’s MAC address with the MAC
address of your Ethernet card.
My Internet
Connection:
Host Name:
MAC Address:
Manual Configuration
Dynamic (Cable)
DNS Addresses:
MTU:
Use Unicasting:
Downloaded from
www.Manualslib.com
manuals search engine
Page 18 / 94
D-Link DIR-6±5 User Manual
Section ² - Configuration
Select
PPPoE (Username/Password)
from the drop-down menu.
Select
Static
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select
Dynamic
.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password in the next
box.
Enter the ISP Service Name (optional).
Select either
Always-on
,
On-Demand
, or
Manual
.
Enter the Primary and Secondary DNS Server Addresses (Static PPPoE
only).
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature,
enable Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is
the default MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not
recommended that you change the default MAC address unless required by your ISP.
You can use the
Clone Your PC’s
MAC Address
button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
My Internet
Connection:
Address Mode:
IP Address:
User Name:
Password:
Service Name:
Reconnection Mode:
Maximum Idle Time:
DNS Addresses:
MTU:
MAC Address:
Internet Setup
PPPoE (DSL)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide
you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE
software from your computer. The software is no longer needed and will not work through a router.
Downloaded from
www.Manualslib.com
manuals search engine
Page 19 / 94
D-Link DIR-6±5 User Manual
Section ² - Configuration
Select
Static
if your ISP assigned you the IP address,
subnet mask, gateway, and DNS server addresses. In most
cases, select
Dynamic
.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses
(Static PPTP only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your PPTP username.
Enter your PPTP password and then retype the password
in the next box.
Select either
Always-on
,
On-Demand
, or
Manual
.
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.
The DNS server information will be supplied by your ISP
(Internet Service Provider.)
Address Mode:
PPTP IP Address:
PPTP Subnet
Mask:
PPTP Gateway:
PPTP Server IP:
Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with
a username and password. This option is typically used for DSL services.
Username:
Password:
Reconnect Mode:
Maximum Idle
Time:
DNS Servers:
Downloaded from
www.Manualslib.com
manuals search engine
Page 20 / 94
±0
D-Link DIR-6±5 User Manual
Section ² - Configuration
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is
the default MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not
recommended that you change the default MAC address unless required by your ISP.
You can use the
Clone Your PC’s
MAC Address
button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
MTU:
MAC Address:
Downloaded from
www.Manualslib.com
manuals search engine

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top