Page 61 / 94 Scroll up to view Page 56 - 60
61
D-Link DIR-6±5 User Manual
Section ³ - Security
Enter the SSID (Service Set Identifier). The SSID is the
name of your wireless network. Create a name using up to
32 characters. The SSID is case-sensitive.
Select the level of security for your wireless network:
• Best - WPA2 Authentication
• Better - WPA Authentication
• Good - WEP Encryption
• None - No security
Click
Next
to continue.
Enter a password between 2-20 characters. The router will
generate a passphrase or key based on your password.
Click
Next
to continue.
Downloaded from
www.Manualslib.com
manuals search engine
Page 62 / 94
D-Link DIR-6±5 User Manual
Section ³ - Security
If you selected Good, the following screen will show you your
WEP key to enter on your wireless clients.
Click
Save
to finish the Security Wizard.
If you selected Better, the following screen will show you your
Pre-Shared Key to enter on your wireless clients.
Click
Save
to finish the Security Wizard.
If you selected Best, the following screen will show you your
Pre-Shared Key to enter on your wireless clients.
Click
Save
to finish the Security Wizard.
If you selected WPA-Enterprise, the RADIUS information will be displayed. Click
Save
to finish the Security Wizard.
Downloaded from
www.Manualslib.com
manuals search engine
Page 63 / 94
D-Link DIR-6±5 User Manual
Section ³ - Security
Configure WEP
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to
the added overhead.
1.
Log into the web-based configuration by opening a
web browser and entering the IP address of the router
(192.168.0.1).
Click on
Setup
and then click
Wireless
Settings
on the left side.
2. Next to
Security Mode
, select
WEP
.
3. Next to
WEP Key Length
, select the level of ecryption (64
or 128-bit) and either
Hex
or
ASCII
.
Hex
- (recommended) Letters A-F and numbers 0-9
are valid.
ASCII
- All numbers and letters are valid.
4. Next to
WEP Key 1
, enter a WEP key that you create.
Make sure you enter this key exactly on all your wireless
devices. You may enter up to 4 different keys.
5. Next to
Authentication
, select
Shared Key
.
6. Click
Save Settings
to save your settings. If you are
configuring the router with a wireless adapter, you will lose connectivity until you enable WEP on your adapter and
enter the same WEP key as you did on the router.
Downloaded from
www.Manualslib.com
manuals search engine
Page 64 / 94
D-Link DIR-6±5 User Manual
Section ³ - Security
Configure WPA-Personal (PSK)
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to
the added overhead.
1.
Log into the web-based configuration by opening a
web browser and entering the IP address of the router
(192.168.0.1).
Click on
Setup
and then click
Wireless
Settings
on the left side.
2. Next to
Security Mode
, select
WPA-Personal
.
3. Next to
WPA Mode
, select
WPA
,
WPA2
, or
WPA2 Only
.
Use
WPA2
if you have wireless clients using both WPA and
WPA2.
4. Next to
Cipher Mode
, select
TKIP, AES,
or
Auto
.
5. Next to
Group Key Update Interval
, enter the amount of time
before the group key used for broadcast and multicast data
is changed (3600 is default).
6. Next to
Pre-Shared Key
, enter a key (passphrase). The key is entered as a pass-phrase in ASCII format at both ends
of the wireless connection. The pass-phrase must be between 8-63 characters.
7. Click
Save Settings
to save your settings. If you are configuring the router with a wireless adapter, you will lose
connectivity until you enable WPA-PSK on your adapter and enter the same passphrase as you did on the router.
Downloaded from
www.Manualslib.com
manuals search engine
Page 65 / 94
65
D-Link DIR-6±5 User Manual
Section ³ - Security
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to
the added overhead.
1.
Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1).
Click on
Setup
and then click
Wireless Settings
on the left
side.
2. Next to
Security Mode
, select
WPA-Enterprise
.
3. Next to
WPA Mode
, select
WPA
,
WPA2
, or
WPA2 Only
. Use
WPA2
if you have wireless clients using both WPA and WPA2.
4. Next to
Cipher Mode
, select
TKIP, AES,
or
Auto
.
5. Next to
Group Key Update Interval
, enter the amount of time
before the group key used for broadcast and multicast data is
changed (3600 is default).
6. Next to
Authentication Timeout
, enter the amount of time before
a client is required to re-authenticate (60 minutes is default).
6. Next to
RADIUS Server IP Address
enter the IP Address of your
RADIUS server.
7. Next to
RADIUS Server Port
, enter the port you are using with your RADIUS server. 1812 is the default port.
8. Next to
RADIUS Server Shared Secret
, enter the security key.
Configure WPA-Enterprise (RADIUS)
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top