Page 21 / 83 Scroll up to view Page 16 - 20
±1
D-Link DIR-615 User Manual
Section ² - Configuration
Enter the IP address of the login server.
Enter your BigPond username.
Enter your BigPond password and then retype
the password in the next box.
Select the type of authentication server being
used.
The default MAC Address is set to the
Internet’s physical interface MAC address on
the Broadband Router. It is not recommended
that you change the default MAC address
unless required by your ISP.
You can use the
Clone Your PC’s MAC Address
button to
replace the Internet port’s MAC address with
the MAC address of your Ethernet card.
BigPond Server:
BigPond Username:
BigPond Password:
Auth Server:
MAC Address:
Internet Setup
Big Pond
Page 22 / 83
±±
D-Link DIR-615 User Manual
Section ² - Configuration
Check the box to enable the wireless function. If you do not
want to use wireless, uncheck the box to disable all the wireless
functions.
Service Set Identifier (SSID) is the name of your wireless network.
Create a name using up to 32 characters. The SSID is case-
sensitive.
Indicates the channel setting for the DIR-615. The Channel can be
changed to fit the channel setting for an existing wireless network
or to customize the wireless network. If you enable
Auto Channel
Scan
, this option will be greyed out.
The
Auto Channel Scan
setting can be selected to allow the
DIR-615 to choose the channel with the least amount of interference.
This feature is enabled by default.
Select one of the following:
802.11g only
- Select if all of your wireless clients are 802.11g.
Mixed 802.11b/g
- Select if you are using both 802.11b and 802.11g wireless clients.
802.11n Only
- Select only if all of your wireless clients are 802.11n.
Mixed 802.11b/g/n
- Select if you are using a mix of 802.11b, 11g, and 11n wireless clients.
Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the router. If Invisible is selected
the SSID will not be seen by site survey utilities so your wireless clients must have the SSID manually entered to connect to
the router.
Refer to page 47 for more information regarding wireless security.
Enable Wireless:
Enable Auto
Channel Scan:
Wireless Settings
Wireless Network
Name:
Wireless Channel:
802.11 Mode:
Visibility Status:
Wireless Security:
Page 23 / 83
±²
D-Link DIR-615 User Manual
Section ² - Configuration
This section will allow you to change the local network settings of the router and to configure the DHCP settings.
Network Settings
Enter the IP address of the router. The default IP
address is 192.168.0.1.
If you change the IP address, once you click Apply,
you will need to enter the new IP address in your
browser to get back into the configuration utility.
Enter the Subnet Mask. The default subnet mask is
255.255.255.0.
Enter the Domain name (Optional).
Uncheck the box to transfer the DNS server
information from your ISP to your computers. If
checked, your computers will use the router for a
DNS server.
IP Address:
Subnet Mask:
Local Domain:
Enable DNS Relay:
Page 24 / 83
±³
D-Link DIR-615 User Manual
Section ² - Configuration
Check this box to enable the DHCP server on
your router. Uncheck to disable this function.
Enter the starting and ending IP addresses for
the DHCP server’s IP assignment.
Note:
If you statically (manually) assign IP
addresses to your computers or devices, make
sure the IP addresses are outside of this range
or you may have an IP conflict.
The length of time for the IP address lease.
Enter the Lease time in minutes.
Refer to the next page for the DHCP Reservation
function.
Enable DHCP
Server:
DHCP IP Address
Range:
Lease Time:
Add DHCP
Reservation:
DHCP Server Settings
DHCP stands for Dynamic Host Control Protocol. The DIR-615 has a built-in DHCP server. The DHCP Server will
automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be
DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers
on, they will automatically load the proper TCP/IP settings provided by the DIR-615. The DHCP Server will automatically
allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and
ending address of the IP address pool.
Page 25 / 83
±5
D-Link DIR-615 User Manual
Section ² - Configuration
DHCP Reservation
If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation.
The router will assign the IP address only to that computer or device.
Note:
This IP address must be within the DHCP IP Address Range.
Check this box to enable the reservation.
Enter the computer name or select from the
drop-down menu and click
<<
.
Enter the IP address you want to assign to the
computer or device. This IP Address must be
within the DHCP IP Address Range.
Enter the MAC address of the computer or
device.
If you want to assign an IP address to the
computer you are currently on, click this button
to populate the fields.
Click
Save
to save your entry. You must click
Save Settings
at the top to activate your
reservations.
Enable:
Computer Name:
IP Address:
MAC Address:
Copy Your PC’s
MAC Address:
Save:

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top