1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DIR-615v3
    5. /
  5. 4
Page 16 / 83 Scroll up to view Page 11 - 15
16
D-Link DIR-615 User Manual
Section ² - Configuration
Select
Dynamic IP (DHCP)
to obtain IP Address
information automatically from your ISP. Select
this option if your ISP does not give you any IP
numbers to use. This option is commonly used
for Cable modem services.
The Host Name is optional but may be required
by some ISPs.
The default MAC Address is set to the Internet
port’s physical interface MAC address on the
Broadband Router. It is not recommended that
you change the default MAC address unless
required by your ISP.
You can use the
Clone
Your PC’s MAC Address
button to replace
the Internet port’s MAC address with the MAC
address of your Ethernet card.
Enter the Primary DNS server IP address
assigned by your ISP.
Maximum Transmission Unit - you may need to
change the MTU for optimal performance with
your specific ISP. 1500 is the default MTU.
My Internet
Connection:
Host Name:
MAC Address:
Manual Configuration
Dynamic (Cable)
DNS Addresses:
MTU:
Page 17 / 83
1´
D-Link DIR-615 User Manual
Section ² - Configuration
Select
PPPoE (Username/Password)
from the drop-down menu.
Select
Static
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select
Dynamic
.
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password in the next
box.
Enter the ISP Service Name (optional).
Enter the IP address (Static PPPoE only).
The default MAC Address is set to the Internet port’s physical interface
MAC address on the Broadband Router. It is not recommended that you
change the default MAC address unless required by your ISP.
You can
use the
Clone Your PC’s MAC Address
button to replace the Internet
port’s MAC address with the MAC address of your Ethernet card.
Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only).
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature,
enable Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is
the default MTU.
Select either
Always-on
,
On-Demand
, or
Manual
.
My Internet
Connection:
Address Mode:
User Name:
Password:
Service Name:
IP Address:
MAC Address:
DNS Addresses:
Maximum Idle Time:
MTU:
Connect Mode:
Internet Setup
PPPoE (DSL)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide
you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE
software from your computer. The software is no longer needed and will not work through a router.
Page 18 / 83
1µ
D-Link DIR-615 User Manual
Section ² - Configuration
Select
Static
if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic
.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses (Static
PPTP only).
Enter the Gateway IP Address provided by your ISP.
The DNS server information will be supplied by your ISP (Internet
Service Provider.)
Enter the Server IP provided by your ISP (optional).
Enter your PPTP account (username).
Enter your PPTP password and then retype the password in the
next box.
Enter a maximum idle time during which the Internet connection is
maintained during inactivity. To disable this feature, enable Auto-
reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the
default MTU.
Select either
Always-on
,
On-Demand
, or
Manual
.
Address Mode:
PPTP IP Address:
PPTP Subnet
Mask:
PPTP Gateway:
DNS Servers:
PPTP Server IP:
Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with
a username and password. This option is typically used for DSL services.
Account:
Password:
Maximum Idle
Time:
MTU:
Connect Mode:
Page 19 / 83
1¶
D-Link DIR-615 User Manual
Section ² - Configuration
Select
Static
if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases,
select
Dynamic
.
Enter the L2TP IP address supplied by your ISP (Static only).
Enter the Subnet Mask supplied by your ISP (Static only).
Enter the Gateway IP Address provided by your ISP.
Enter the Primary and Secondary DNS Server Addresses (Static
L2TP only).
Enter the Server IP provided by your ISP (optional).
Enter your L2TP account (username).
Enter your L2TP password and then retype the password in the
next box.
Enter a maximum idle time during which the Internet connection
is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is
the default MTU.
Select either
Always-on
,
On-Demand
, or
Manual
.
Address Mode:
L2TP IP Address:
L2TP Subnet Mask:
L2TP Gateway:
DNS Servers:
L2TP Server IP:
Account:
Password:
Maximum Idle Time:
MTU:
Connect Mode:
Internet Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
Page 20 / 83
±0
D-Link DIR-615 User Manual
Section ² - Configuration
Enter the IP address assigned by your ISP.
Enter the Subnet Mask assigned by your ISP.
Enter the Gateway assigned by your ISP.
The default MAC Address is set to the Internet port’s
physical interface MAC address on the Broadband
Router. It is not recommended that you change the
default MAC address unless required by your ISP.
You can use the
Clone Your PC’s MAC Address
button to replace the Internet port’s MAC address
with the MAC address of your Ethernet card.
The DNS server information will be supplied by your
ISP (Internet Service Provider.)
Maximum Transmission Unit - you may need to
change the MTU for optimal performance with your
specific ISP. 1500 is the default MTU.
IP Address:
Subnet Mask:
ISP Gateway:
MAC Address:
DNS Servers:
MTU:
Internet Setup
Static (assigned by ISP)
Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address,
subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the
appropriate IP form, which are four octets separated by a dot (x.x.x.x). The router will not accept the IP address if it is not in this format.

Rate

4.5 / 5 based on 2 votes.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top