D-Link DIR-330 Router Manual PDF (Setup & Configuration Guide)

Page 26 / 114 Scroll up to view Page 21 - 25

21

D-Link DIR-330 User Manual

Section 3 - Conﬁguration

Enter the IP address assigned by your ISP.

Enter the Subnet Mask assigned by your

ISP.

Enter the Gateway assigned by your ISP.

The default MAC Address is set to the Internet

port’s physical interface MAC address on the

Broadband Router. It is not recommended that

you change the default MAC address unless

required by your ISP.

You can use the

Clone

MAC Address

button to replace the Internet

port’s MAC address with the MAC address of

your Ethernet card.

The DNS server information will be supplied

by your ISP (Internet Service Provider.)

You may need to change the MTU (Maximum

Transmission Unit) for optimal performance

with your speciﬁc ISP. 1500 is the default

MTU.

IP Address:

Subnet Mask:

ISP Gateway:

MAC Address:

DNS Servers:

MTU:

Internet Setup

Static IP

Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address,

subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the ﬁelds must be in the

appropriate IP form, which are four octets separated by a dot (x.x.x.x). The router will not accept the IP address if it is not in this format.

Page 27 / 114

22

D-Link DIR-330 User Manual

Section 3 - Conﬁguration

Select

PPPoE (Username/Password)

from

the drop-down menu.

In most cases, select

Dynamic

. Select

Static

if your ISP assigned you the IP address,

subnet mask, gateway, and DNS server

addresses.

Enter your PPPoE user name.

Enter your PPPoE password and then retype

the password in the next box.

Enter the ISP Service Name (optional).

Enter the IP address (Static PPPoE only).

The default MAC Address is set to the Internet

port’s physical interface MAC address on the

Broadband Router. It is not recommended

that you change the default MAC address

unless required by your ISP.

You can use

the

Clone MAC Address

button to replace

the Internet port’s MAC address with the MAC

address of your Ethernet card.

Enter a maximum idle time during which the

Internet connection is maintained during

inactivity. To disable this feature, enable

Always-on

(Connect Mode option below).

My Internet

Connection:

Address Mode:

User Name:

Password:

Service Name:

IP Address:

MAC Address:

Maximum Idle Time:

Internet Setup

Russian PPPoE

Choose Russian PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will

provide you with a username and password. This option is typically used for DSL services. Make sure to remove your

PPPoE software from your computer. The software is no longer needed and will not work through a router.

Page 28 / 114

23

D-Link DIR-330 User Manual

Section 3 - Conﬁguration

You may need to change the MTU

(Maximum Transmission Unit) for

optimal performance with your speciﬁc

ISP. 1492 is the default MTU.

Select either

Always-on

,

Manual

, or

Connect

On-Demand

.

In most cases, select Dynamic PPPoE.

Select Static PPPoE if your ISP assigned

you the IP address, subnet mask,

gateway, and DNS server addresses.

Enter the IP address (Static IP only).

Enter the Subnet Mask supplied by your

ISP (Static IP only).

Enter the Primary and Secondary DNS

Server Addresses (Static IP only).

MTU:

Connect Mode:

WAN Physical

Setting:

IP Address:

Subnet Mask:

DNS Addresses:

Page 29 / 114

24

D-Link DIR-330 User Manual

Section 3 - Conﬁguration

Enter the Server IP provided with your ISP.

Enter your PPTP account (username).

Enter your PPTP password and then retype the password in

the next box.

Enter a maximum idle time during which the Internet connection

is maintained during inactivity. To disable this feature, enable

Always-on

(Connect Mode option below).

You may need to change the MTU (Maximum Transmission

Unit) for optimal performance with your speciﬁc ISP. 1450 is

the default MTU.

Click either Always-on, Manual, or Connect-on demand.

In most cases, select either Dynamic IP. Select Static IP if

your ISP assigned you the IP address, subnet mask, gateway,

and DNS server addresses.

Enter the IP address (Static IP only).

Enter the Subnet Mask supplied by your ISP (Static IP

only).

Enter the Gateway provided by your ISP (Static IP only).

Click the

Clone MAC Address

button to copy the MAC

Address from your PC.

Enter the Primary and Secondary DNS Server Addresses (Static IP only).

Server IP/Name:

PPTP Account:

PPTP Password:

Maximum Idle

Time:

MTU:

Connect Mode:

WAN Physical

Setting:

IP Address:

Subnet Mask:

Gateway:

Clone MAC

Setting:

DNS Setting:

Internet Setup

Russian PPTP

Choose Russian PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide

you with a username and password. This option is typically used for DSL services.

Page 30 / 114

25

D-Link DIR-330 User Manual

Section 3 - Conﬁguration

Check the box to enable WPS.

WPS uses this PIN (Personal Identification

Number) to establish the wireless network. You

can generate a new PIN or reset the PIN to its

default setting.

Click this button if you don’t want to further

conﬁgure the settings of WPS and only need to

use one PIN.

Click this button if you want to add a wireless

device with WPS. In the screen that follows, you

can enter the wireless device’s PIN or click a

virtual push button to add a wireless device.

Enable:

Current PIN:

Reset to

Unconﬁgured:

Add Wireless

Device With

WPS:

Wireless Settings

Wi-Fi Protected Setup (WCN 2.0)

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share