D-Link DI-614+ Router Manual PDF (Setup & Configuration Guide)

Page 26 / 74 Scroll up to view Page 21 - 25

26

Using the Conﬁguration Menu

Advanced > Applications

Some applications require multiple connections, such as Internet gaming, video

conferencing, and Internet telephony. These applications have difﬁculties working

through NAT (Network Address Translation).

Special Applications

makes some of these

applications work with the DI-614+. If you need to run applications that require multiple

connections, specify the port normally associated with an application in the

Trigger

ﬁeld, then enter the public ports associated with the trigger port into the

Incoming Ports

ﬁeld.

At the bottom of the screen, there are already deﬁned special applications. To use them,

select one from the drop down list and select an ID number you want to use. Then click

the “Copy to” button and the router will ﬁll in the appropriate information to the list. You

will then need to enable the service. If the mechanism of Special Applications fails to

make an application work, try using DMZ host instead.

Note!

Only one PC can use each Special Application tunnel.

Trigger Port

This is the port used to trigger the application. It can be either

a single port or a range of ports.

Public Ports

This is the port number on the WAN side that will be used to

access the application. You may deﬁne a single port or a range

of ports. You can use a comma to add multiple ports or port

ranges.

Enabled or

Disabled

Select to activate or deactivate the policy.

Name

You can name the deﬁned special applications.

Public Type

Select the public type the special application will use.

Select the trigger protocol you would like to initiate. To chage

the selection, use the drop down arrow and other choices will

be listed.

Trigger Type

Page 27 / 74

27

Using the Conﬁguration Menu

Advanced > Filters > IP Filter

Schedule

IP Address

Enter the IP address range of the computers that you want the

policy to apply to. If it is only a single computer that you want

the policy applied to, then enter the IP address of the computer

in the Start Source IP and leave the End Source IP blank.

Use IP (Internet Protocol) ﬁlters to allow or deny computers access to the Internet

based on their IP address.

Port Range

Enter in the port range of the TCP/UDP ports that you want

the policy to apply to. If it is only a single port that you want the

policy applied to, then enter the port number in the Start Port

ﬁeld and leave the End Port ﬁeld blank. If you want to use all

the ports, you can leave the port range empty.

Enabled or Disabled

Click

Enabled

to apply the ﬁlter policy or click

Disabled

to enter

an inactive ﬁlter policy. (You can reactivate the policy later.)

Select

Always

, or choose

From

and enter the time period during

which the IP ﬁlter policy will be in effect.

Protocol Type

Select the protocol type to allow or deny certain types of IP

addresses.

Page 28 / 74

28

Using the Conﬁguration Menu

Advanced > Filters > MAC Filters

MAC (Media Access Control) Filters are used to deny or allow LAN (Local Area Network)

computers from accessing the Internet and network by their MAC address.

At the bottom of the screen, there is a list of MAC addresses from the DHCP client

computers connected to the DI-614+. To use them, select one from the drop down

list and select an IP number you want to use. Then click the “Copy to” button and the

DI-614+ will ﬁll in the appropriate information in the list.

Only allow computers with MAC address listed below to access the network

Select this option to only allow computers that are in the list

to access the network and Internet. All other computers will

be denied access to the network and Internet.

Only deny computers with MAC address listed below to access the network

Select this option to only deny computers that are in the list

to access the network and Internet. All other computers will

be allowed access to the network and Internet.

Enter the

MAC Address

of the client that will be ﬁltered.

MAC Address

Name

Enter a name to create a proﬁle for the associated

computer(s) on the network.

Select from the DHCP Client list and click the Clone button to

automatically clone that computer’s MAC address to the MAC

address ﬁeld.

DHCP Client

Disabled MAC Filter

Select this option if you do not want to use MAC ﬁlters.

Page 29 / 74

29

Using the Conﬁguration Menu

Advanced > Parental Control >URL Blocking

Use URL Blocking to deny LAN computers from accessing speciﬁc web sites by its

URL. A URL is a specially formatted text string that deﬁnes a location on the Internet.

If any part of the URL contains the blocked word, the site will not be accessible and

the web page will not display.

Disabled URL Blocking

Select this option if you do not want to use URL Blocking.

Page 30 / 74

30

Using the Conﬁguration Menu

Advanced > Parental Control > Domain Blocking

Use Domain ﬁlters to allow or deny computers access to speciﬁc Internet domains

whether it is through www, ftp, SNMP, etc.

Domain ﬁlters apply to both wired computers

connected to one of the four Ethernet LAN ports and to wireless clients connected

wirelessly to the DI-614+.

Disabled Domain Filter

Select this option if you do not want to use Domain ﬁlters.

Allow users to access the following domains and block all other domains

Select this option to allow users to access the speciﬁed

Internet domains listed below.

Users will be denied access

to all other Internet domains.

Deny users to access the following domains and permit all other domains

Select this option to deny users access to the speciﬁed

Internet domains listed below. Users will be allowed access

to all other Internet domains.

Permitted/Blocked Domains

This is a list of domain sufﬁxes of the Internet domain you

want to permit or block. (Example: shopping.com,

sports.net.)

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share