Page 36 / 60
Scroll up to view Page 31 - 35
36
Troubleshooting
2. The wireless client cannot access the Internet in the Infrastructure
mode.
•
Make sure the wireless client is associated and joined with the correct
router.
To check this connection:
Right-click
on the
Local Area
Connection icon
in the taskbar> select
View Available Wireless
Networks
.
The
Connect to Wireless Network
screen will appear.
Please make sure you have selected the correct available network, as
shown in the illustrations below.
•
Check that the
IP Address
assigned to the wireless adapter is within
the same
IP Address range
as the gateway.
Since the DI-514 has
an IP Address of
192.168.0.1, wireless adapters must have an IP
Address in the same range, e.g., 192.168.0.x.
Each device must
have a unique IP Address; no two devices may have the same IP
Address. The subnet mask must be the same for all the computers
on the network.)
To check the
IP Address
assigned to the wireless
adapter,
double-click
on the
Local Area Connection icon
in the
taskbar > select the
Support tab
and the
IP Address
will be
displayed.
(Please refer to
Checking the IP Address
in the
Networking Basics
section of this manual.)
•
If it is necessary to assign a
Static IP Address
to the wireless
adapter, please refer to the appropriate section in
Networking
Basics
.
If you are entering a
DNS Server address
you must also
enter the
Default Gateway Address.
(Remember that if you have a
DHCP-capable router, you will not need to assign a Static IP Address.
See
Networking Basics: Assigning a Static IP Address.
)
Default
Page 37 / 60
37
Troubleshooting
3.
Check that the drivers for the network adapters are installed
properly.
You may be using different network adapters than those illustrated here, but this
procedure will remain the same, regardless of the type of network adapters you are
using.
•
Go to
Start
•
Right-click
on
My Computer
•
Click
Properties
•
Select
the
Hardware Tab
•
Click
Device
Manager
NOTE
: Screen shots taken using
Windows XP. If you are using a
different Operating System your
screen may look different.
Page 38 / 60
38
Troubleshooting
•
Double-click
on
Network
Adapters
•
Right-click
on
D-Link
Air
Plus DWL-650
Wireless Cardbus
Adapter
•
Select
Properties
to check
that the drivers are
installed properly
•
Look
under
Device
Status
to check that the
device is working properly.
•
Click
OK
D-Link
Air
DWL-650 Wireless Cardbus Adapter
D-Link
Air
Plus DWL-650+ Wireless Cardbus Adapter
D-Link AirPlus DWL-650 Wireless Cardbus Adapter
Page 39 / 60
39
Troubleshooting
4.
Resetting the DI-514 to Factory Default Settings
After you have tried other methods for troubleshooting your network, you
may choose to
Reset
the DI-514 to the factory default settings.
Remember that D-Link Plus products network together, out of the box, at
the factory default settings.
To hard-reset the D-Link Plus DI-514 to Factory Default Settings, please do
the following:
•
Leave the device powered on, do not disconnect the power
•
Press the reset button and hold (use a paper clip)
•
Keep the button pressed about 10 seconds
•
Release the button
The DI-514 will then automatically reboot itself.
Page 40 / 60
40
7. Networking Basics
Using the Network Setup Wizard in Windows XP
In this section you will learn how to establish a network at home or work,
using
Microsoft Windows XP.
Note:
Please refer to websites such as
and
for information about
networking computers using Windows 2000, ME or 98.
Go to
Start>Control Panel>Network Connections
Select
Set up a home or small office network
When this screen appears,
Click Next.
19216811.live