D-Link DGL-4100 Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

D-Link

DGL-4100

Page 26 / 62 Scroll up to view Page 21 - 25

Using the Configuration Interface

D-Link Systems, Inc.

Name:

Priority:

Protocol:

Source IP Range:

Source Port Range:

Destination IP Range:

Destination Port

Range:

Save:

Add/Edit GameFuel

™

Rule

Automatic classification should be adequate for most applications. GameFuel rules identify a specific

message flow and assign priority to that flow.

Create a name for the rule that is meaningful to you.

The priority of the message flow is entered here. O receives the highest

priority (most urgent) and 255 receives the lowest priority.

The protocol used by the messages.

The rule applies to a flow of messages whose LAN-side IP address is within

the range set here.

The rule applies to a flow of messages whose LAN-side port number is

within the range set here.

The rule applies to a flow of messages whose WAN-side IP address is

within the range set here.

The rule applies to a flow of messages whose WAN-side port number is

within the range set here.

Saves the new rule or modified existing rule to the Rules list. When you are

done editing the settings, you must click the Save Settings button at the top

of the page to make the changes effective and permanent.

GameFuel Rules List

Entries on this list can be enabled/disabled by toggling the Enable checkbox. Entries can be modified

by clicking on the paper and pencil icon. To delete an entry, click on the trash can icon. After you’ve

completed all modifications or deletions, you must click the

Save Settings

button at the top of the

page to save your changes. The router must reboot before new settings will take effect. You will be

prompted to

Reboot the Device

Continue

. If you need to make additional settings changes, click

Continue

. If you are finished with your configuration settings, click the

Reboot the Device

button.

Downloaded from

www.Manualslib.com

manuals search engine

Page 27 / 62

Using the Configuration Interface

D-Link Systems, Inc.

Routing

Add/Edit Route

Adds a new route to the IP routing table or edits an existing route.

Specifies whether the entry will be enabled or disabled.

The IP address or network that the packets will be attempting to access

Note: 192.168.1.0 with a Netmask of 255.255.255.0 means traffic will be

routed to the entire 192.168.1.x network.

Used to specify which portion of the Destination IP signifies the network

trying to be accessed and which part signifies the host that the packets will

be routed to

Note: 255.255.255.255 is used to signify only the host that was entered in

the Destination IP field.

Specifies the next hop to be taken if this route is used. A gateway of 0.0.0.0

implies there is no next hop, and the IP address matched is directly connected

to the router on the interface specified: LAN or WAN.

Specifies the interface, LAN or WAN, that the IP packet must use to transit

out of the router when this route is used.

The amount of hops it will take to reach the Destination IP or network.

hop is considered to be traffic passing through a router from one network to

another.

If there is only one router between your network and the Destination

network, then the Metric value would be 1.

Saves the new rule or modified existing rule to the Rules list. When you are

done editing the settings, you must click the Save Settings button at the top

of the page to make the changes effective and permanent.

Route List

This section shows the current routing table entries. Certain required routes are predefined and

cannot be changed. Entries on this list that can modified can be enabled/disabled by toggling the

Enable checkbox. Editable entries can be modified by clicking on the paper and pencil icon. To delete

an editable entry, click on the trash can icon. After you’ve completed all modifications or deletions,

you must click the

Save Settings

button at the top of the page to save your changes. The router must

reboot before new settings will take effect. You will be prompted to

Reboot the Device

Continue

If you need to make additional settings changes, click

Continue

. If you are finished with your

configuration settings, click the

Reboot the Device

button.

Enable:

Destination IP:

Netmask:

Gateway:

Interface:

Metric:

Save:

Advanced > Routing

Downloaded from

www.Manualslib.com

manuals search engine

Page 28 / 62

Using the Configuration Interface

D-Link Systems, Inc.

Access Control

The Access Control section allows you to control access in and out of your network. Use this feature

as Parental Controls to only grant access to approved sites, limit web access based on time or dates,

and/or block access from applications like P2P utilities or games.

Enabled

By default the Access Control feature is disabled. If you enable Access Control, every device on the

LAN must either have a static IP address (that is one that is not in the DHCP range) or must be in the

Static DHCP Client List (see Basic > DHCP).

When Access Control is disabled, every device on the LAN is permitted to access the Internet.

However, if you enable Access Control, every device on the LAN that needs to access the Internet

must have an Access Control rule that explicitly permits it to access the Internet. Devices that do not

have an Access Control Rule cannot access the Internet. When Access Control is enabled, the

options below will appear:

Add/Edit Access Control Rule

Create a name for this access control policy that is meaningful to you. Typically

this would be a system name or user name such as Rob’s PC.

The local network IP address of the machine that you want the access

control rule to apply to. Example: 192.168.0.50. Make sure that this is a

static IP address or the system is in the static DHCP Client list (See Basic >

DHCP).

Select a schedule of times when you want the policy to apply. If you do not

see the schedule you need in the list of schedules, go to the Tools >

Schedules screen and create a new schedule.

With this option enabled, the specified system will only have access to the

Web sites listed in the Web filter section.

If this option is enabled, all of the Web sites visited by the specified machine

will be logged.

By clicking the Filter Ports >> button you can specify that the rule enables

access only to specific IP addresses and ports.

Saves the new or edited access control rule in the Access Control Rules

List. Repeat the process, creating an Access Control Rule for each of the

devices on your LAN that needs access to the Internet. When finished

updating Access Control Rules, you must still click the Save Settings button

at the top of the page to make changes effective and permanent.

Policy Name:

Machine IP Address:

Schedule:

Apply Web Filter:

Log Internet Access:

Filter Ports:

Save:

Advanced > Access Control

Downloaded from

www.Manualslib.com

manuals search engine

Page 29 / 62

Using the Configuration Interface

D-Link Systems, Inc.

Access Control Rules List

This section shows the current Access Control rules. Any device that does not have a rule, cannot

access the Internet. Entries can be modified by clicking on the paper and pencil icon. To delete an

entry, click on the trash can icon. After you’ve completed all modifications or deletions, you must click

the

Save Settings

button at the top of the page to save your changes. The router must reboot before

new settings will take effect. You will be prompted to

Reboot the Device

Continue

. If you need to

make additional settings changes, click

Continue

. If you are finished with your configuration settings,

click the

Reboot the Device

button.

Web Filter

The Web Filter section is where you add the Web site to be used for Access Control.

Add/Edit Web Site

This field is where you can add Web sites to the Allowed Web List. The Allowed Web List is used for

systems that have the Web filter option enabled in Access Control.

Entries in the Allowed Web Site List can be activated or deactivated with

this checkbox. New entries are activated by default.

Enter the URL (address) of the web site that you want to allow (such as

google.com

). Enter the most inclusive domain name. For instance, entering

dlink.com will give you access to www.dlink.com and support.dlink.com.

not enter

the

http://

preceding the URL.

Note: Many web sites construct pages with images and content from other

web sites. Access will be forbidden if you do not enable all of the web sites

used to construct a page. For example, to access my.yahoo.com, you must

enable access to yahoo.com, yimg.com, and doubleclick.net.

Saves the new or modified Allowed Web Site in the Allowed Web Site List.

When you are done editing the settings, you must click the Save Settings

button at the top of the page to make the changes effective and permanent.

Allowed Web Site List

This section lists the currently allowed web sites. Entries can be modified by clicking on the paper

and pencil icon. To delete an entry, click on the trash can icon. After you’ve completed all modifications

or deletions, you must click the

Save Settings

button at the top of the page to save your changes.

The router must reboot before new settings will take effect. You will be prompted to

Reboot the

Device

Continue

. If you need to make additional settings changes, click

Continue

. If you are

finished with your configuration settings, click the

Reboot the Device

button.

Enable:

Web Site:

Save:

Advanced > Web Filter

Downloaded from

www.Manualslib.com

manuals search engine

Page 30 / 62

Using the Configuration Interface

D-Link Systems, Inc.

Mac Address Filters

The MAC (Media Access Controller) Address filter section is used to control network access based

on the MAC Address of the network adapter. A MAC address is a unique ID assigned by the

manufacturer of a networking device. This feature can be configured to ALLOW or DENY network/

Internet access.

Filter Settings

When this is enabled, depending on the mode selected, computers are

granted or denied network access based on their MAC address.

When Allow is selected, only computers with MAC addresses listed in the

MAC Address List are granted network access. When Deny is selected, any

computer with a MAC address listed in the MAC Address List

Add MAC Address

MAC address entries are activated or deactivated with this checkbox.

Enter the MAC address of the desired computer or connect to the router

from the desired computer and click Copy Your PC’s MAC Address button.

Saves the new or modified MAC address in the MAC Address List. When

you are done editing the settings, you must click the Save Settings button at

the top of the page to make the changes effective and permanent.

MAC Address List

This section lists the current MAC address filters. Entries can be modified by clicking on the paper

and pencil icon. To delete an entry, click on the trash can icon. After you’ve completed all modifications

or deletions, you must click the

Save Settings

button at the top of the page to save your changes.

The router must reboot before new settings will take effect. You will be prompted to

Reboot the

Device

Continue

. If you need to make additional settings changes, click

Continue

. If you are

finished with your configuration settings, click the

Reboot the Device

button.

MAC Filter Enabled:

Mode:

Enable:

MAC Address:

Save:

Advanced > MAC Address Filter

Downloaded from

www.Manualslib.com

manuals search engine

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share