D-Link DCS-5300G Router Manual PDF (Setup & Configuration Guide)

Page 131 / 145 Scroll up to view Page 126 - 130

131

There is a button hidden in the pinhole on the side of the

DCS-5300G

. It

is used to

reset

the system or

restore

the factory default settings.

Sometimes resetting the

DCS-5300G

will return the system back to a

normal state. If the system still has problems after reset, restore the

factory settings and install again:

RESET

:

1. Lightly insert a paper clip (or a similar sized tool) into the

reset hole on the side of the camera, press lightly and

then release the button.

2. The LED on the front of the camera will begin blinking red

and green.

3. When the LED stops the blinking the reset has completed.

RESTORE

:

1. Insert the paper clip or other tool, press on the button,

and hold it down.

2. Wait for the LED on the front of the camera to blink red

and green and hold the button through two cycles of

blinking (about 5-7 seconds.)

3. Withdraw the tool after the second cycle of the LED

blinking and a factory restore has been completed.

Reset and Restore

Restoring the factory defaults will result in the

loss of any previous settings and will require

running the

Installation Wizard

to find the

camera’s IP address.

Reset button

Page 132 / 145

132

I/O Connector Definition for the Internet Camera

The

DCS-5300G

provides a general I/O terminal block with one digital input

and one relay switch for device control. Pin 1 and pin 2 can be connected to an

external sensor and the state of voltage will be monitored from the initial state

‘LOW’. The relay switch of pin 3 and pin 4 can be used to turn the external

device on or off.

The I/O connector provides the physical interface for digital output (DO) and

digital input (DI) that is used for connecting a diversity of external alarm devices

to the Internet Camera such as IR-Sensors and alarm relays.

I/O Connector

The digital input is used for connecting external alarm devices and once triggered

images will be taken and e-mailed.

1

DI+

INPUT (Max. 50mA, 12VDC)

2

DI-

INPUT (Initial state of DI is low)

3

SW_COMMON

OUTPUT (open from SW_OPEN at initial state)

(close with SW_OPEN when set DO to ON)

4

SW_NOPEN

OUTPUT (Max. 1A, 24VDC or 0.5A, 125VAC)

I/O Terminal Block:

I/O Connector

Page 133 / 145

133

The above diagram shows a typical wiring configuration for a normally closed

PIR motion sensor. Please refer to your specific motion sensor for the power

supply connection to the device since this will be critical to the success of your

installation. Note that the positive from the PIR is connected to the D- of the I/O

port of the camera and the negative from the PIR is connected to the D+ of the

camera I/O port.

Configuring Your Camera for External Trigger Based Recording

I/O Connector (continued)

To configure your camera to record when triggered by an external device,

you must first set your SMTP or FTP settings in order to send snapshots to

your email account or FTP server.

Page 134 / 145

134

In this window, enter the settings for the SMTP or FTP server to which recorded

snapshots will be sent. For detailed information about each setting, please refer

to

Configuration > Advanced > Mail & FTP

in the section titled “Using the

DCS-5300G With an Internet Browser” (page 42). Click the apply button when

finished.

Configuring Your Camera for External Trigger Based Recording

(continued)

I/O Connector (continued)

Next, click the

Mail & FTP

button under the

Advanced

tab to set the SMTP or

FTP server settings for the

DCS-5300G

.

Click

Mail & FTP

Page 135 / 145

135

Configuring Your Camera for External Trigger Based Recording

(continued)

I/O Connector (continued)

In this window, follow the steps below to set the application settings for

snapshots to be sent to your email account or FTP server when triggered by a

motion sensor or other external device:

c

Select the weekdays you would like to record and enter the

“Snapshots begin” time and “Snapshots end” time for the weekly

schedule, or select “All the time except for the above schedule” if you

want to enable full time snapshot recording.

d

Check “Event operation.”

e

Set the delay “before detecting next event” to avoid continuous false

alarms following the original event.

f

Set the delay to “take snapshots after event” to capture the direction

of the moving object.

5

Check the trigger condition for input and motion detection (in this

case “Input is Low”).

6

Check “Trigger output alarm while input condition matched” and

“Upload snapshots while motion detected.”

7

Select to either send snapshots by email or by FTP.

Click the apply button when finished. You are now able to send snapshots,

based on triggered recording, to your email account or FTP server.

Next, click the

Applications

button under the

Tools

tab to

set the application settings for

the

DCS-5300G

.

Click

Applications

X

Living room

X

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share