Page 66 / 145
Scroll up to view Page 61 - 65
66
Record Snapshots to your FTP server with
Motion Detection (continued)
1st FTP password-
Specify the password to access the external FTP
server (e.g. 12345).
1st FTP remote folder-
Specify the destination folder in the external FTP
server (e.g. snapshot).
Primary FTP passive
mode-
Passive mode will allow access to an external
FTP server if your camera is behind a router
protected by a firewall.
2nd FTP server-
Specify the Domain name or IP address of your
second external FTP server. This field is optional
if you have already filled in the information for the
first FTP server.
2nd FTP user name-
Specify the user name to access your backup
FTP server.
2nd FTP password-
Specify the user password to your backup FTP
server.
2nd FTP remote folder-
Specify the destination folder on your external
backup FTP server.
For detailed information about each setting, please refer to
Configuration >
Advanced > Mail & FTP
in the section titled “Using the DCS-5300G With an
Internet Browser” (page 42). Click the apply button when finished.
Secondary FTP passive
mode-
Passive mode will allow access to a second
external FTP server if your camera is behind a
router protected by a firewall.
1st FTP user name-
Specify the user name to access the external FTP
server (e.g. John Smith).
3
4
5
6
Page 67 / 145
67
Next, click the
Applications
button under the
Tools
tab to set the application
settings for the
DCS-5300G
.
In this window, follow the steps below to set the application settings for
snapshots to be recorded to an FTP site:
c
Select the weekdays you would like to record and enter the
“Snapshots begin” time and “Snapshots end” time for the weekly
schedule, or select “All the time except for the above schedule” if you
want to enable full time snapshot recording.
d
Check “Event operation.”
e
Set the delay “before detecting next event” to avoid continuous false
alarms following the original event.
f
Set the delay to “take snapshots after event” to capture the direction
of the moving object.
5
Check the window name (in this case Living room).
6
Check “Upload snapshots while motion detected.”
7
Click “Send snapshots by FTP” and check “FTP put snapshots with
date and time suffix”
8
Click the “Apply” button to save the settings.
Click the apply button when finished. You are now able to record snapshots to
your FTP server when motion detection is triggered.
Click
Applications
Record Snapshots to your FTP server with
Motion Detection (continued)
X
X
X
X
X
X
Living room
Page 68 / 145
68
Using IP surveillance Software
Installing the IP surveillance Software
Before you begin installing this application software, the hardware system
requirements must be checked first. The minimum system requirements
recommended for this application are as follows:
Browser: Internet Explorer 5.x or above
CPU: Intel Pentium III 800MHz or above
(Pentium 4, 2GHz plus processor with 512MB memory and a 32MB video card
is required for multiple camera viewing and recording in IP Surveillance)
SDRAM: 128MB SDRAM
Hard Disk: 40GB
Video Card: nVidia, TNT, TNT2, GeForce series with 32MB video memory / ATI
Radeon series with 32MB video memory
Put the installation disk into your CD-ROM, and it will run automatically. If it
does not, open “My Computer” and double click on the CD-ROM icon. Next the
installation menu will appear. Click “Install Software”. The following window will
appear.
Click
IP surveillance
Page 69 / 145
69
Using IP surveillance Software (continued)
The “License Agreement” window below will appear. Please read the following
license agreement carefully. Click “Yes” to accept this agreement and proceed
with the installation.
Click
Next
Click
Yes
Installing the IP surveillance software (continued)
Page 70 / 145
70
Using IP surveillance Software (continued)
Next, the “User information” window below will appear. This window will prompt
you to enter the user name and company name. Enter your user name and
company name and then click “Next” to continue.
Click
Next
You must setup the administrator’s password in order to proceed. Input and
confirm your password in the window shown in below. Click “Next” to continue.
Click
Next
Installing the IP surveillance software (continued)
19216811.live