Page 11 / 72
Scroll up to view Page 6 - 10
10
D-Link DCS-5300 User Manual
Select the Program folder that Setup will add program icons to. You may type a new
folder name, or select one from the existing folders list.
Please wait while the Installation Wizard is installed.
Installation is now complete.
Click
Next
Click
Finish
Page 12 / 72
11
D-Link DCS-5300 User Manual
IMPORTANT:
A hardware reset of the Network Camera may be required if the
Installation Wizard cannot find the camera. To accomplish
this reset, lightly insert a paper clip (or a similar sized tool) into the reset hole on the back of the camera (see page
64 for the location of the reset
hole). The LED on the front of the camera will begin blinking orange. When it stops
the blinking cycle continue to hold in the reset button until a second cycle of blinking red and green lights indicates a
second reset cycle has completed. This will take approximately 5-7 seconds.
To access the Installation Wizard screen, click on the
Installation
Wizard
icon on your desktop.
The opening Installation Wizard screen will appear and
show
a MAC address of the DCS-5300 and an IP Address (which
may or may not be correct depending on what you have your
DCS-5300 connected to). If you have a DHCP* server on
your network, there will be a valid IP Address displayed here,
indicated by a “Yes” under the assigned column.
*A DHCP server is a device that supplies IP Addresses to its
clients that are on the same network.
Page 13 / 72
12
D-Link DCS-5300 User Manual
The Installation Wizard will now show a MAC address for the DCS-5300 and an IP address. This IP address may not be
correct at this step in the installation until you see “Yes” under the assigned column. The camera is now automatically
configured with an IP address consistent to the device it is connected to.
You have now completed the Setup Wizard and are ready to use your camera!
For more information regarding the functions of this screen, see the following section titled “Installation Wizard
Screen.”
Select
the MAC address
Click on the
Link to Selected Devices
button.
After you click on the
Link to Selected Devices
button, Installation
Wizard
will automatically open your Internet browser to the IP Address
Your DCS-5300
may have a different IP Address.
Page 14 / 72
13
D-Link DCS-5300 User Manual
The following options are available on the Installation Wizard screen by clicking on the corresponding tab:
Click to search for any available cameras to connect to the network.
Click to manually add a camera to the network. A window will appear, prompting
you to enter the camera’s IP address or domain name. A second window will
appear, prompting you to enter the port number.
Click to remove the selected camera(s) from the network.
Click to uncheck all selected cameras.
Click to link all selected devices to the network.
On the initial Setup Screen you can configure System and Date/Time settings for
each camera. Click
Next
to configure Network settings for the camera.
Installation Wizard Screen
Search:
Add:
Remove:
Uncheck All:
Links to Selected
Devices:
Enter a Camera Name and create a Root password for the camera.
Enter the Date and Time for each camera. These settings can also be configured
on the
Tools > System
screen (page 53) when configuring the camera via a
Web browser.
System Settings:
Date/Time
Settings
:
Page 15 / 72
14
D-Link DCS-5300 User Manual
Click
Next
and then
Apply
to save the configured settings. Users can click
Previous
to modify changes or mistakes.
After the settings have been saved, click the
Done
button that appears.
Here users can configure the Network Settings for the camera. Enter the IP
address, Subnet mask, Default router IP, Primary DNS, and Secondary DNS.
Automatically, the option to reset IP address at boot is selected. If you would like
to save your IP address settings, make sure to uncheck this box. These settings
can also be configured on the
Advanced > Network screen
(page 38) when
configuring the camera via a Web Browser.
Network Settings:
19216811.live