1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DCS-3420
    5. /
  5. 12
Page 56 / 149 Scroll up to view Page 51 - 55
²³
D-Link DCS-34±0 User Manual
Section 3 - Configuration
Specify the destination folder in the external FTP server (e.g. 123456).
Passive mode will allow access to an external FTP server if your camera is behind a router protected by
a firewall.
Specify the Domain name or IP address of your second external FTP server. This field is optional if you
have already filled in the information for the first FTP server.
The port of the FTP server. The default is 21 for an external FTP site.
Specify the user name to access your backup FTP server.
Specify the user password to your backup FTP server.
Specify the destination folder on your external backup FTP server.
Passive mode will allow access to a second external FTP server if your camera is behind a router protected
by a firewall.
1st FTP remote
folder:
Primary FTP
passive mode:
2nd FTP server:
2nd FTP sever port:
2nd FTP user name:
2nd FTP password:
2nd FTP remote
folder:
Secondary FTP
passive mode:
Page 57 / 149
²´
D-Link DCS-34±0 User Manual
Section 3 - Configuration
For detailed information about each setting, please
refer to Configuration > Advanced > Mail & FTP in the
section titled “Using the DCS-3420 With an Internet
Browser” (page 30). Click the apply button when
finished.
Next, click the Applications button under the Tools tab
to set the application settings for the DCS-3420.
In this window, follow the steps below to set the
application settings for snapshots to be recorded to
an FTP site:
1. Select the weekdays you would like to record
and enter the “Snapshots begin” time and
“Snapshots end” time for the weekly schedule, or
select “All the time except for the above schedule” if
you want to enable full time snapshot recording.
2. Check “Event operation.” Set the delay “before
detecting next event” to avoid continuous false
alarms following the original event. Set the
“Snapshot Interval” to capture the direction of the
moving object.
3. Check the window name.
4. Check “Upload snapshots while motion
detected.”
5. Click “Send snapshots by FTP” and check “FTP
put snapshots with date and time suffix.”
6. Click the “Apply” button to save the settings.
Click the apply button when finished. You are now able to record snapshots to your FTP server when motion
Page 58 / 149
²8
D-Link DCS-34±0 User Manual
Section 3 - Configuration
I/O Connector
I/O Connector Definition for the Internet Camera
The DCS-3420 provides a general I/O terminal block with one digital input and one relay switch for device control. The
relay switch of pin 1 and pin 2 can be used to turn the external device on or off. Pin 3 and pin 4 can be connected
to
an external sensor and the state of voltage will be monitored from the initial state ‘LOW’
The I/O connector provides the physical interface for digital output (DO) and digital input (DI) that is used for connecting
a diversity of external alarm devices to the Internet Camera such as IR-Sensors and alarm relays.
The digital input is used for connecting external alarm devices and once triggered images will be taken and e-mailed.
1
SW_COMMON OUTPUT (open from SW_OPEN at initial state)(close with SW_OPEN when set DO to ON)
2
SW_OPEN OUTPUT (Max. 1A, 24VDC or 0.5A, 125VAC)
3
DI+INPUT (Max. 50mA, 12VDC)
4
DI-INPUT (Initial state of DI is low)
I
/
O
Page 59 / 149
²µ
D-Link DCS-34±0 User Manual
Section 3 - Configuration
The above diagram shows a typical wiring configuration for a normally closed PIR motion sensor. Please refer to your
specific motion sensor for the power supply connection to the device since this will be critical to the success of your
installation. Note that the positive from the PIR is connected to the D+ of the I/O port of the camera and the negative
from the PIR is connected to the D- of the camera I/O port.
Configuring Your Camera for External Trigger Based Recording
To configure your camera to record when triggered by an external device, you must first set your SMTP or FTP set
-
tings in order to send snapshots to your email account or FTP server.
DI/DO Connection Diagram
Page 60 / 149
³0
D-Link DCS-34±0 User Manual
Section 3 - Configuration
Click the
Network
button under the
Advanced
tab to set the SMTP or FTP server settings for the
DCS-3420.
In this window, enter the settings for the SMTP or
FTP server to which recorded snapshots will be sent.
For detailed information about each setting, please
refer to
Configuration > Advanced > Mail & FTP
(page 37). Click the
Apply
button when finished.

Rate

3.5 / 5 based on 2 votes.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top