D-Link DCS-3220 Router Manual PDF (Setup & Configuration Guide)

Page 56 / 141 Scroll up to view Page 51 - 55

56

Configuration > Tools > Default

Click on the

Default

button to access the option to restore to factory default

settings.

Click

Apply

on this screen to restore factory default settings. This means

any

changes made will be lost and the system will be reset to the initial status when

shipped from the factory. After confirmation, the system will restart and require

the

Installation Wizard

software program to locate the IP address of the

DCS-

3220

.

Using the DCS-3220 with an Internet browser

(continued)

Click

Apply

to make

changes effective

.

Configuration > Status > Device Info

Click on the

Status

tab to access

Device Info

and a

Log

of

DCS-3220

system

activity. The

Device Info

is the default screen when you click on the

Status

tab.

Click

Default

.

Page 57 / 141

57

The Device Info screen lists the following important settings that are currently

set for the

DCS-3220

.

•

Firmware Version number

•

Mac Address

•

IP Address

•

Subnet Mask

•

Default router address

•

Primary DNS Address

•

Secondary DNS Address

Configuration > Status > Log

Using the DCS-3220 with an Internet browser

(continued)

Click on the

Log

button to access a system log of system activity from the

Status

menu. The content of the log file reveals useful information about the

current configuration and connection logged after the

DCS-3220

boots up.

Click

Device Info

.

Click

Log

.

Page 58 / 141

58

Click on the

Help tab

to access descriptions of the particular function you need

help with. The help screen is organized in the order of the tabs and then each

menu item under that tab.

Configuration > Help

Using the DCS-3220 with an Internet browser

(continued)

Page 59 / 141

59

Administrators can combine options on the application page to perform many

useful security applications. There are two trigger sources available: from an

external sensor or with built-in motion detection. There are also two kinds of

actions that can respond to these events that include uploading snapshots

over the internet and driving attached devices. To upload the snapshots, users

can choose either email or FTP according to user’s needs. Both e-mail and

FTP use the network settings on the network page. This section describes

how to enable motion detection and record snapshots to an FTP server.

If no external sensor is available, administrators can utilize the built-in motion

detection to monitor any abnormal movement and record the snapshots to an

FTP or SMTP server.

In this window, follow the steps below to ensure that motion detection is correctly

enabled:

c

Check “Enable motion detection.”

d

Click on “New” to have a new window to monitor video.

e

Enter in a window name.

f

Tune the “Sensitivity” and “Percentage” according to the local

environment. The highest sensitivity and lowest percentage provides

the most sensitive setting.

5

Click on save to enable the activity display.

Click the

Motion Detection

button under the

Advanced

tab from the

Configuration

screen to access settings that affect how the

DCS-3220

Internet

Camera can serve as a security device by recording only when motion is

detected.

Record Snapshots to your FTP server

with Motion Detection

Click

Motion Detection

.

Back Door

X

Page 60 / 141

60

Next, click the

Network

button under the

Advanced

tab to set the FTP server

settings for the

DCS-3220

.

Record Snapshots to your FTP server with

Motion Detection (continued)

In this window, enter the settings for the FTP server you wish to record to.

Optionally, you can enter settings for a secondary backup FTP server.

Local FTP server port-

The Default port is 21. To connect to an FTP sever,

it is recommended that you do not change the

port number unless your camera is behind a

router. If your camera is behind a router, you can

assign any port number to this field, but you must

enable port forwarding on the router. Please refer

to your router manual for more information on port

forwarding.

1st FTP server-

If you are going to upload snapshots to an FTP

server, you will need to fill in the Domain name or

IP address of your external FTP server such as

ftp://dlink.com or ftp://123.123.123.1. (The server

name and IP address will vary

depending on the

user.) The following user settings must be

correctly configured for remote access.

1

2

Click

Network

John Smith

123.123.123.1

1

2

3

4

Snapshot

5

6

7

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share