D-Link DCM-202 Router Manual PDF (Setup & Configuration Guide)

Page 11 / 31 Scroll up to view Page 6 - 10

11

D-Link DCM-202 User Manual

Section 2 - Installation

Verify the TCP/IP Conﬁguration

Before installing the modem using the Ethernet setup, you must verify that your computer has the TCP/IP protocol installed. Follow

the procedure for your operating system to verify or install the TCP/IP protocol.

To conﬁgure TCP/IP on your Windows

®

Vista

™

PC:

1. Right click on

Start->Network

and select

Properties

2. On the the following pop up window, select

Tasks->Manage network connections

.

3. Right-click

Local Area Connection

and click

Properties

. Look for an entry named TCP/IP. If you see TCP/IP listed next to your

Ethernet hardware device, you can now go to the section “Connecting the Cable Modem.” However, if TCP/IP is not listed, you

must complete the following steps.

• Scroll to the

Internet Protocol version 4 TCP/IP

option.

• Click to place a check mark in the Internet Protocol check box

• Click OK.

• You can now connect the cable modem.

To conﬁgure TCP/IP on your Windows 2000/XP PC:

1. Right-click the

My Network Places

icon on the Windows desktop.

2. Right-click

Local Area Connection

and click

Properties

. Look for an entry named TCP/IP. If you see TCP/IP listed next

to your Ethernet hardware device, you can now go to the section “Connecting the Cable Modem.” However, if TCP/IP is

not listed, you must complete the following steps.

• Scroll to the Internet Protocol TCP/IP option.

• Click to place a check mark in the Internet Protocol check box

• Click

OK

.

• You can now connect the cable modem.

Page 12 / 31

12

D-Link DCM-202 User Manual

Section 2 - Installation

Network Overview

Below are two common ways to connect your DCM-202 modem to your network. The diagram on the left shows the connection with

a broadband router. The diagram on the right shows the connection directly to a computer.

Page 13 / 31

13

D-Link DCM-202 User Manual

Section 2 - Installation

Connecting the Cable Modem

Install the cable modem according to the following procedure:

1. Power off the computer.

2. Unplug the computer from the electrical wall outlet.

3. Make these connections:

• Connect the coaxial cable to the cable modem’s CATV cable connector. If you plan to have the cable connected

to a television as well as the cable modem, you must use a cable line splitter (not included).

• Plug the cable modem’s power adapter into a wall outlet or surge protector and into the cable modem’s

power jack.

• Plug one end of the Ethernet cable into the cable modem’s Ethernet port and the other end of the cable into

the existing NIC.

4. Plug in the computer.

5. Power on the computer. When installation is complete, your setup should resemble the illustration above. The

modem is operating properly if the Power, Cable, Status and ETH light emitting diodes (LEDs) are solid green

(lit and not blinking).

Page 14 / 31

14

D-Link DCM-202 User Manual

Section 2 - Installation

Using the USB Port

This section describes how to install the cable modem using the USB port. First you connect the hardware (cable modem and power

adapter). You then install the software drivers and verify that the modem is operating properly. The USB port does not support the

Macintosh

®

operating system. Using the USB port to connect to the Internet enables you to install the cable modem more quickly

and easily than connecting to the Internet using the computer’s Ethernet port, because you do not have to remove the case from the

computer to install a network interface card (NIC). Using the USB port, however, enables you to connect only one computer to the

cable modem. See “Installing the Cable Modem Using the Ethernet Port” if you wish to install the cable modem using the Ethernet

port.

If you have or plan on purchasing a router, please refer to the “Using the Ethernet Port” section on page 11. You cannot use the USB

connection with a router.

Note:

Do not plug the USB modem into an external USB hub. Plug directly to your computer.

Page 15 / 31

15

D-Link DCM-202 User Manual

Section 2 - Installation

Network Overview

The diagram below displays the connect of your DCM-202 modem to your computer using the USB cable.

Installing the Hardware

To install the hardware:

1. Connect the coaxial cable to the cable modem’s CATV cable connector.

2. Connect the USB cable to the modem (not the computer).

3. Plug the power adapter into the modem. Plug the other end into a wall outlet or power strip.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share