Page 86 / 100 Scroll up to view Page 81 - 85
86
D-Link DAP-1522 User Manual
Section 5 - Connecting to a Wireless Network
Click
Connect Anyway
to continue.
The utility will display the following window to indicate a
connection is being made.
The final window indicates the establishment of a successful
connection.
The next two pages display the windows used to connect to
either a WEP or a WPA-PSK wireless network.
Page 87 / 100
87
D-Link DAP-1522 User Manual
Section 5 - Connecting to a Wireless Network
Click on a network (displayed using the SSID) using WEP
under Select a network to connect to and then click the
Connect
button.
Enter the appropriate security key or passphrase in the field
provided and then click the
Connect
button.
Configure WEP
It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter.
If you are joining an existing network, you will need to know the WEP key being used.
Page 88 / 100
88
D-Link DAP-1522 User Manual
Section 5 - Connecting to a Wireless Network
Click on a network (displayed using the SSID) using WPA-PSK
under Select a network to connect to and then click the
Connect
button.
Enter the appropriate security key or passphrase in the field
provided and then click the
Connect
button.
Configure WPA-PSK
It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter.
If you are joining an existing network, you will need to know the WEP key being used.
Page 89 / 100
89
D-Link DAP-1522 User Manual
Section 6 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DAP-1522.
Read the following descriptions if you are having problems.
(The examples below are illustrated in Windows
®
XP.
If
you have a different operating system, the screenshots on your computer will look similar to the following examples.)
1. Why can’t I access the web-based configuration utility?
When entering the IP address of the D-Link access point (192.168.0.50 for example), you are not connecting to a
website on the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the
device itself. Your computer must be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
• Internet Explorer 7.0 or higher
• Firefox 3.0 or higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using
a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may
not be on.
• Disable any internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice,
Sygate, Norton Personal Firewall, and Windows
®
XP firewall may block access to the configuration pages. Check the
help files included with your firewall software for more information on disabling or configuring it.
Page 90 / 100
90
D-Link DAP-1522 User Manual
Section 6 - Troubleshooting
• Configure your Internet settings:
• Go to
Start > Settings > Control Panel
. Double-click the
Internet Options
Icon. From the Security tab,
click the button to restore the settings to their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings
button. Make sure nothing is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three
times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link access point in the
address bar. This should open the login page for your the web management.
• If you still cannot access the configuration, unplug the power to the access point for 10 seconds and plug back in.
Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a
different computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your access point. Unfortunately this process will change all your settings
back to the factory defaults.
To reset the access point, locate the reset button (hole) on the rear panel of the unit. With the access point powered
on, use a paperclip to hold the button down for 10 seconds. Release the button and the access point will go through
its reboot process. Wait about 30 seconds to access the access point. The default IP address is 192.168.0.50. When
logging in, the username is admin and leave the password box empty.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top