Page 11 / 75
Scroll up to view Page 6 - 10
Conceptronic C300BRS4
User Manual
11
A.
Right click the Wireless
Network Icon in your
System tray and select
“
View Available Wireless
Networks
”.
B.
Select the Network
“
C300BRS4
” from the list
of available wireless
networks and click
“
Connect
”.
C.
You will receive a warning
about connecting to an
unsecured wireless
network. Click “
Connect
anyway
” to proceed with
the connection.
D.
When the connection is
built, you will see the
active wireless icon in the
system tray. If you move
your mouse over the icon
you will receive an
information popup (about
the speed, signal strength
and status of your
connection).
A
B
B
C
Page 12 / 75
Conceptronic C300BRS4
User Manual
12
Computer Configuration
Configure your IP address
The C300BRS4 is equipped with a build-in DHCP Server. The DHCP Server will automatically assign an
IP address to a connected computer if the connected computer is set to “
obtain an IP address
automatically
”.
To configure your computer for Automatic IP follow the instructions below:
A.
Click “
Start
”
Æ
“
Run
”.
B.
Enter the command “
NCPA.CPL
”
and press “
OK
”.
The Network Connections window will appear.
C.
Right click your “
Local Area Connection
”
(Wired or Wireless, depending on the
connection you use) and select
“
Properties
”.
B
B
C
Page 13 / 75
Conceptronic C300BRS4
User Manual
13
The Properties window of your Local Area Connection will appear.
D.
Select the “
Internet Protocol
(TCP/IP)
” and click
“
Properties
”.
The Properties window of the Internet Protocol (TCP/IP) will appear.
E.
Set the properties to “
Obtain
an IP address automatically
”
and press “
OK
” to save the
settings.
F.
Press “
OK
” in the properties
window of the Local Area
Connection to save the settings.
D
D
E
E
Page 14 / 75
Conceptronic C300BRS4
User Manual
14
Checking your connection with the C300BRS4
With the Command prompt of Windows you can verify if you have received a correct IP address on
your Local Area Connection:
A.
Click “
Start
”
Æ
“
Run
”.
B.
Enter the command “
CMD
” and press “
OK
”.
The Command Prompt will appear.
C.
Enter the command “
IPCONFIG
” and press
ENTER
.
You should see the following information
IP Address
:
192.168.0.xxx
(Where
xxx
can vary between
100 ~ 199
).
Subnet Mask
: 255.255.255.0
Default Gateway
:
192.168.0.1
If the information shown above matches your configuration you can continue the configuration of
the device in Chapter 5.
If the shown information above does not match your configuration (i.e. your IP address is
169.254.xxx.xxx) please check the options below:
1.
Power OFF and Power ON the device.
2.
Reconnect the LAN Cable to the device and to your computer.
3.
Renew the IP address of your computer with the following commands:
- “
IPCONFIG /RELEASE
” to release the wrong IP address.
- “
IPCONFIG /RENEW
” to receive a new IP address from the device.
C
Page 15 / 75
Conceptronic C300BRS4
User Manual
15
If above steps do not solve the IP address problem, you can reset the device to the factory default
settings with the Reset Button on the back of the device.
Press and hold the Reset Button for +/- 15 seconds to load the Factory Default Settings. When the
Status LED is active again, repeat step
C
to renew your IP address.
3
3
19216811.live