Page 126 / 199 Scroll up to view Page 121 - 125
VPN
Viewing the Summary Information for VPN
Cisco Small Business RV0xx Series Routers Administration Guide
126
9
Viewing the Summary Information for VPN
The
VPN > Summary
page displays general information about the router’s VPN
tunnel settings. The router supports up to 100 tunnels.
NOTE
If the PPTP Server is enabled, summary information about PPTP clients appears on
the
VPN > PPTP Server
page. For more information, see
Setting Up PPTP Server,
page 150
.
To open this page:
Click
VPN > Summary
in the navigation tree.
Summary
Tunnel(s) Used:
The number of VPN tunnels in use.
Tunnels Available:
The number of available VPN tunnels.
Detail:
Click
Detail
for more information. Click
Refresh
to update the data,
or click
Close
to return to the
VPN > Summary
page. For each VPN tunnel,
the No., Name, Status, Phase 2 Enc/Auth/Grp, Local Group, Remote Group,
and Remote Gateway will be displayed.
Page 127 / 199
VPN
Viewing the Summary Information for VPN
Cisco Small Business RV0xx Series Routers Administration Guide
127
9
Tunnel Status
Above the table, the following information appears:
Tunnel(s) Enabled:
The number of tunnels that are enabled.
Tunnel(s) Defined:
The number of tunnels that are defined, including
enabled and disabled tunnels.
The table displays the following information about each tunnel:
No.:
The identification number of the VPN tunnel.
Name:
A descriptive name for the VPN tunnel.
Status:
The status of the VPN tunnel:
Connected
or
Waiting for Connection.
Phase2 Enc/Auth/Grp:
The Phase 2 Encryption type (NULL/DES/3DES/
AES-128/AES-192/AES-256), Authentication method (NULL/MD5/SHA1),
and DH Group number (1/2/5) that you chose in the IPSec Setup section.
If you selected Manual for the Keying Mode in the IPSec section, then only
the Encryption type and Authentication method appear.
Local Group:
The IP address and subnet mask of the Local Group.
Remote Group:
The IP address and subnet mask of the Remote Group.
Remote Gateway:
The IP address of the Remote Gateway.
Tunnel Test:
Click
Connect
to verify the status of the VPN tunnel. The test
result will be updated in the
Status
column. If the tunnel is connected, a
Disconnect button will be available so you can end the connection.
Configure:
Click the
Edit
icon to open a new page where you can change
the tunnel’s settings. To delete tunnel settings, select a tunnel, and then click
the
Delete
icon
Tunnel Enabled:
The number of enabled VPN tunnels.
Tunnel Defined:
The number of defined VPN tunnels.
Add:
Click this button to add a tunnel. Then choose one of the following
options:
-
To create a tunnel for a remote site with a VPN router, choose
Gateway
to Gateway
. The
Gateway to Gateway
page appears. See
Setting Up a
Gateway to Gateway (Site to Site) VPN, page130
.
Page 128 / 199
VPN
Viewing the Summary Information for VPN
Cisco Small Business RV0xx Series Routers Administration Guide
128
9
-
To create a tunnel for a remote worker using VPN client software, choose
Client to Gateway
. The
Client to Gateway
page appears. See
Setting
Up a Remote Access Tunnel for VPN Clients (Client To Gateway),
page 139
.
Navigation controls:
If you have numerous rules, you can adjust the display.
Use the
Rows per page list
at the top right corner of the table to choose the
number of rules to display on each page. Use the
Page
list below the table
to choose a particular page. Use the navigation buttons to view the first
page, previous page, next page, or final page. Some buttons may be
unavailable, depending on the number of pages and the current selection.
GroupVPN Status
If you enable the GroupVPN setting for any of your Client to Gateway tunnels, the
status information appears in this table.
Group Name:
A descriptive name for the group VPN.
Connected Tunnels:
The number of users logged into the group VPN.
Phase2 Enc/Auth/Grp:
The Phase 2 Encryption type (NULL/DES/3DES/
AES-128/AES-192/AES-256), Authentication method (NULL/MD5/SHA1),
and DH Group number (1/2/5), as configured in the
IPSec Setup
section.
Local Group:
The IP address and subnet mask of the Local Group.
Remote Client:
The remote clients in the group VPN.
Remote Clients Status:
The status of the remote clients:
Online
or
Offline
.
Click
Detail List
to open the
Group List
window. This window displays the
Group Name, IP address, and Connection Time. You can click
Refresh
to
update the data, or click
Close
to close the pop-up window and return to
the
VPN > Summary
page.
Tunnel Test:
Click
Connect
to verify the status of the group VPN. The test
result will be updated in the
Status
column. If the group VPN is connected, a
Disconnect button will be available so you can end the connection.
Configure:
Click the
Edit
icon to open a new page where you can change
the tunnel’s settings. To delete tunnel settings, select a tunnel, and then click
the
Delete
icon.
Navigation controls:
If you have numerous rules, you can adjust the display.
Use the
Rows per page list
at the top right corner of the table to choose the
number of rules to display on each page. Use the
Page
list below the table
to choose a particular page. Use the navigation buttons to view the first
Page 129 / 199
VPN
Viewing the Summary Information for VPN
Cisco Small Business RV0xx Series Routers Administration Guide
129
9
page, previous page, next page, or final page. Some buttons may be
unavailable, depending on the number of pages and the current selection.
VPN Clients Status
This section identifies the VPN clients currently connected to the router.
No.:
The ID number of the VPN client.
Username:
The name of the VPN client.
Status:
The status of the VPN client connection.
Start Time:
The time when the VPN client established its VPN connection
to the router.
End Time:
The time when the VPN client ended its VPN connection to the
router.
Duration:
The period of time that the VPN connection has been active.
Disconnect
: Click this button to disconnect any VPN client.
Navigation controls:
If you have numerous rules, you can adjust the display.
Use the
Rows per page list
at the top right corner of the table to choose the
number of rules to display on each page. Use the
Page
list below the table
to choose a particular page. Use the navigation buttons to view the first
page, previous page, next page, or final page. Some buttons may be
unavailable, depending on the number of pages and the current selection.
Page 130 / 199
VPN
Setting Up a Gateway to Gateway (Site to Site) VPN
Cisco Small Business RV0xx Series Routers Administration Guide
130
9
Setting Up a Gateway to Gateway (Site to Site) VPN
Use the
VPN > Gateway to Gateway
page to create a new tunnel between two
VPN devices, such as a Cisco RV082 router at your office and a Cisco RV042
router at a remote office.
You will enter the settings for the local group and the remote group, and you will
enter the corresponding settings (reversing “local” and “remote”) when configuring
the other router. A successful connection requires that at least one router is
identifiable by a static IP address or a Dynamic DNS hostname. Alternatively, if one
router has only a dynamic IP address, you can use any email address as
authentication to establish the connection.
NOTE
The two ends of the tunnel cannot be on the same subnet. For example, if the Site A
LAN uses the 192.168.1.x subnet, Site B could use 192.168.2.x.
You will enter corresponding settings (reversing “local” and “remote”) when
configuring the two routers. When you configure this router (Router A), enter its
settings in the
Local Group Setup
section, and enter the settings for the other
router (Router B) in the
Remote Group Setup
section. When you configure the
other router (Router B), enter its settings in the
Local Group Setup
section, and
enter the Router A settings in the
Remote Group Setup
section. For more details
and examples, see
Appendix D, “Configuring a Gateway-to-Gateway VPN
Tunnel Between RV0xx Series Routers.”
.
To open this page:
Click
VPN > Gateway to Gateway
in the navigation tree.
Alternatively, you can click the
Add Tunnel
button on the
VPN > Summary
page, in
the
Tunnel Status
section. Then choose
Gateway to Gateway
.
199468
Site A
RV016
router
RV042
router
Site B
Inside
192.168.1.1/24
Outside
209.165.200.226/24
Outside
209.165.200.236/24
Inside
192.168.2.1/24
Personal
computers
Personal
computers
Printer
Printer
Internet

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top