Page 16 / 106 Scroll up to view Page 11 - 15
16
4021192 Rev B
Back Panel Description
Back Panel Description
The following illustrations show the description and function of the back panel
components on the Cisco DPC3925 residential gateway.
1
POWER
Connects the residential gateway to the AC power adapter that is
provided with your residential gateway
CAUTION:
Avoid damage to your equipment. Only use the power supply
that is provided with your residential gateway.
2
ON/OFF SWITCH (European models only)
Allows you to power of the
residential gateway without removing the power cord
3
MAC ADDRESS LABEL
Displays the MAC address of the residential gateway
4
TELEPHONE 1 and 2
RJ-11 telephone ports connect to home telephone wiring
to conventional telephones or fax machines
5
USB
Connects to selected client devices
6
ETHERNET
Four RJ-45 Ethernet ports connect to the Ethernet port on your PC
or your home network
7
CABLE
F-connector connects to an active cable signal from your service
provider
Page 17 / 106
4021192 Rev B
17
Back Panel Description
8
WIRELESS SETUP
Pressing this switch initiates wireless setup, this feature
allows the user to add new Wi-Fi Protected Setup (WPS) compliant wireless
clients to the home network
9
RESET
A momentary pressing (1-2 seconds) of this switch reboots the EMTA.
Pressing the switch for more than ten seconds first causes a reset-to-factory-
default of all settings and then reboots the gateway
CAUTION:
The Reset button is for maintenance purposes only. Do not use
unless instructed to do so by your cable or telephone service
provider. Doing so may cause you to lose any cable modem
settings you have selected.
Page 18 / 106
18
4021192 Rev B
What Are the System Requirements for Internet Service?
What Are the System Requirements for Internet Service?
To ensure that your residential gateway operates efficiently for high-speed Internet
service, verify that all of the Internet devices on your system meet or exceed the
following minimum hardware and software requirements.
Note:
You will also need an active cable input line and an Internet connection.
Minimum System Requirements for a PC
A PC with a Pentium MMX 133 processor or greater
32 MB of RAM
Web browsing software
CD-ROM drive
Minimum System Requirements for Macintosh
MAC OS 7.5 or later
32 MB of RAM
System Requirements for an Ethernet Connection
A PC with Microsoft Windows 2000 operating system (or later) with TCP/IP
protocol installed, or an Apple Macintosh computer with TCP/IP protocol
installed
An active 10/100/1000BASE-T Ethernet network interface card (NIC) installed
Page 19 / 106
4021192 Rev B
19
How Do I Subscribe to High-Speed Internet and Telephone Service?
How Do I Subscribe to High-Speed Internet and Telephone
Service?
Before you can use your residential gateway, you need to have a high-speed Internet
access account. If you do not have a high-speed Internet access account, you need to
set up an account with your local service provider. Choose one of the options in this
section.
I Do Not Have a High-Speed Internet Access Account
If you do
not
have a high-speed Internet access account, your service provider will
set up your account and become your Internet Service Provider (ISP). Internet access
enables you to send and receive e-mail, access the World Wide Web, and receive
other Internet services.
You will need to give your service provider the following information:
The serial number of the modem
The Media Access Control (MAC) address of the modem (CM MAC)
Other MAC address numbers as needed
These numbers appear on a bar code label located on the residential gateway. The
serial number consists of a series of alphanumeric characters preceded by
S/N
. The
MAC address consists of a series of alphanumeric characters preceded by
CM MAC
.
The following illustration shows a sample bar code label.
Write down these numbers in the space provided here.
Serial Number
_______________________
MAC Address
________________________
Page 20 / 106
20
4021192 Rev B
How Do I Subscribe to High-Speed Internet and Telephone Service?
I Already Have an Existing High-Speed Internet Access Account
If you have an existing high-speed Internet access account, you must give your
service provider the serial number and the MAC address of the residential gateway.
Refer to the serial number and MAC address information listed previously in this
section.
I Want to Use the Application Server for Telephone Service
You will also need to set up a telephone account with your local service provider to
use your residential gateway for telephone service. When you contact your service
provider, you may be able to transfer your existing telephone numbers, or your cable
telephony service provider will assign a new telephone number for each current or
additional active telephone line. Discuss these options with your telephony service
provider.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top