1. Home
    2. /
  2. Manuals
    3. /
  3. CBN Inc
    4. /
  4. CG6640E
    5. /
  5. 4
Page 16 / 70 Scroll up to view Page 11 - 15
13
9.
For a second telephone, plug the telephone wire of a single-line telephone into the
TEL 2
port on the rear of the CH6640E.
10. Check that the LEDs on the front panel cycle through the following sequence:
CH6640E/CG6640E LED Activity During Startup
LED
Description
POWER
Turns
on
when
AC
power
is
connected
to
the
CH6640E/CG6640E.
Indicates that the power is connected properly.
RECEIVE
Flashes while scanning for the downstream receive channel.
Changes to solid green when single downstream channel is
locked.
Changes to solid blue when multiple downstream channels
are locked.
SEND
Flashes while scanning for the upstream send channel.
Changes to solid green when single upstream channel is
locked.
Changes to solid blue when multiple upstream channels are
locked.
ONLINE
Flashes
during
CH6640E/CG6640E
registration
and
configuration.
Changes to solid green when the CH6640E/CG6640E is
registered successfully and ready for Internet access
Page 17 / 70
14
Wall Mounting the CH6640E/CG6640E
You have the option to wall mount the CH6640E/CG6640E. Do the following before
mounting the CH6640E/CG6640E on the wall:
•
Locate the unit as specified by the local or national codes governing residential or
business cable TV and communications services.
•
Follow all local standards for installing a network interface unit/network interface
device (NIU/NID).
•
Make sure the AC power plug is disconnected from the wall outlet and all cables are
removed from the back of the CH6640E/CG6640E before starting the installation.
•
Decide if you want to mount the CH6640E/CG6640E horizontally or vertically.
If possible, mount the unit to concrete, masonry, a wooden stud, or some other very solid
wall material. Use anchors if necessary (for example, if you must mount the unit on
drywall).
CAUTION:
Before drilling holes, check the structure for potential
damage to water, gas, or electrical lines.
Do the following to mount your CH6640E/CG6640E on the wall:
1.
Print a copy of the
Wall Mounting Template.
2.
Measure the printed template with a ruler to ensure that it is the correct size.
3.
Use a center punch to mark the center of the holes.
4.
On the wall, locate the marks for the mounting holes.
5.
Drill the holes to a depth of at least 1 1/2 inches (3.8 cm). Use M3.5 x 38 mm (#6 x
11/2 inch) screws with a flat underside and maximum screw head diameter of 9.0 mm
to mount the CH6640E/CG6640E.
6.
Using a screwdriver, turn each screw until part of it protrudes from the wall, as shown
in the following wall mounting screw dimensions illustration.
6.0 mm (.24 inches) maximum
9.0 mm (.35 inches) maximum
2.5 mm (.10 inches).
There must be .10 inches (2.5 mm) between the wall and the underside of the screw
head.
7.
Place the CH6640E/CG6640E so the keyholes on the back of the unit are aligned
above the mounting screws.
Page 18 / 70
15
8.
Slide the CH6640E/CG6640E down until it stops against the top of the keyhole
opening.
9.
After mounting, reconnect the coaxial cable input and Ethernet connection.
10. Plug the power cord into the +12VDC connector on the gateway and the electrical
outlet.
11. Route the cables to avoid any safety hazards.
Page 19 / 70
16
Wall Mounting Template
Figure 1 Wall Mounting Template
Setting Up Internet Access
After installing the CH6640E/CG6640E, check that you can connect to the Internet. You
can retrieve an IP address for your computer’s network interface using one of the
following options:
•
Retrieve the statically defined IP address and DNS address
•
Automatically retrieve the IP address using the Network DHCP server
The CBN CH6640E/CG6640E Wireless Gateway provides a DHCP server on its LAN. It
is recommended that you configure your LAN to obtain the IPs for the LAN and DNS
server automatically.
Make sure all computers on your LAN are configured for TCP/IP. After configuring
TCP/IP on your computer, you should verify the IP address.
Note
: For UNIX or Linux systems, follow the instructions in the
applicable user documentation.
Page 20 / 70
17
Configuring TCP/IP in Windows XP
1.
Open the
Control Panel
.
2.
Double-click
Network Connections
to list the Dial-up and LAN or High-Speed
Internet connections.
3.
Right-click the network connection for your network interface.
4.
Select
Properties
from the drop-down menu to display the Local Area Connection
Properties window. Be sure Internet Protocol (TCP/IP) is checked.
5.
Select
Internet Protocol (TCP/IP)
and click
Properties
to display the Internet
Protocol (TCP/IP) Properties window.
6.
Select
Obtain an IP address automatically
and
Obtain DNS server address
automatically
.
7.
Click
OK
to save the TCP/IP settings and exit the TCP/IP Properties window.
8.
Close the Local Area Connection Properties window and then exit the Control Panel.
9.
When you complete the TCP/IP configuration, continue with Verifying
the IP Address
in Windows XP
.
Configuring TCP/IP in Windows Vista
1.
Open the
Control Panel
.
2.
Click
Network and Internet
to display the Network and Internet window.
3.
Click
Network and Sharing Center
to display the Network and Sharing Center
window.
4.
Click
Manage network connections
to display the LAN or High-Speed Internet
connections window.
5.
Right-click the network connection for the network interface you want to change.
6.
Click
Properties
to display the Local Area Connection Properties window.
Vista may prompt you for an administrator password or confirmation. Type the
password or confirmation, then click
Continue
.
7.
Click
Networking
tab, then select
Internet Protocol Version 4 (IPv4)
.
8.
Click
Properties
to display the Internet Protocol Version 4 (TCP/IPv4) Properties
window.
9.
Select
Obtain an IP address automatically
and
Obtain DNS server address
automatically
.
10. Click
OK
to save the TCP/IP settings and close the Internet Protocol Version 4
(TCP/IPv4) Properties window.
11. Click
OK
to close the Local Area Connection Properties window.
12. Close the remaining windows and exit the Control Panel.
13. When you complete the TCP/IP configuration, continue with Verifying the IP Address
in Windows Vista.
Verifying the IP Address in Windows XP
To check the IP address:
1.
On the Windows Desktop, click
Start
.
2.
Select
Run
. The Run window is displayed.
3.
Type
cmd
and click
OK
.

Rate

124.8 / 5 based on 304 votes.

Popular CBN Inc Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top