CBN Inc CG6640E Router Manual PDF (Setup & Configuration Guide)

Page 6 / 70 Scroll up to view Page 1 - 5

3

Sample Wireless Network Connections (CH6640E model shown)

Sample Wireless Network Connections (CG6640E model shown)

Your maximum wireless operation distance depends on the type of materials through

which the signal must pass and the location of your CH6640E/CG6640E and clients

(stations). CBN cannot guarantee wireless operation for all supported distances in all

environments.

Note

:

To

get

better

wireless

coverage,

please

put

your

CH6640E/CG6640E wireless gateway vertically.

Page 7 / 70

4

Wired Ethernet LAN

You can easily connect any PC with an Ethernet cable to the CH6640E/CG6640E

Ethernet port. Because the CH6640E/CG6640E Ethernet port supports auto-MDIX

,

you

can use a straight-through or cross-over cable to connect a hub, switch, or computer.

Use category 5, or better, cabling for all Ethernet connections.

Sample Ethernet to Computer Connection (CH6640E model shown)

Sample Ethernet to Computer Connection (CG6640E model shown)

Page 8 / 70

5

A wired Ethernet LAN with more than four computers requires one or more hubs,

switches, or routers. You can:

•

Connect a hub or switch to any Ethernet port on the CH6640E/CG6640E.

•

Use Ethernet hubs, switches, or routers to connect up to any combination of 253

computers and wireless clients to the CH6640E/CG6640E.

More detailed information on Ethernet cabling is beyond the scope of this document.

Front Panel

The CH6640E/CG6640E front panel contains indicator lights and the

WPS button

which

is used to configure Wi-Fi Protected Security (WPS) on compatible clients connected to

the CH6640E/CG6640E network.

The CH6640E front panel LED indicators provide the following status information for

power, communications, and errors:

LED

Flashing

On

1

POWER

Not applicable — LED does not

flash

Green

: Power is properly connected

2

RECEIVE

Scanning

for

a

downstream

channel connection

Green

:

Downstream

channel

is

connected

Blue

:

Downstream

channel

is

connected with bonded channels

3

SEND

Scanning for an upstream channel

connection

Green

:

Upstream

channel

is

connected

Blue

:

Upstream

channel

is

connected with bonded channels

4

ONLINE

Scanning for Internet connection;

transmitting or receiving data over

the Internet

Green

: Connected to Internet

Page 9 / 70

6

LED

Flashing

On

5

TEL1

TEL 2

Telephone is off-hook; dialing or

call in progress

Green

: Telephone is connected and

activated; on-hook

6

WIRELESS

Amber

: WPS function is enabled.

Green

: Wi-Fi wireless interface is

active now.

The CG6640E front panel LED indicators provide the following status information for

power, communications, and errors:

LED

Flashing

On

1

POWER

Not applicable — LED does not

flash

Green

: Power is properly connected

2

RECEIVE

Scanning

for

a

downstream

channel connection

Green

:

Downstream

channel

is

connected

Blue

:

Downstream

channel

is

connected with bonded channels

3

SEND

Scanning for an upstream channel

connection

Green

:

Upstream

channel

is

connected

Blue

:

Upstream

channel

is

connected with bonded channels

4

ONLINE

Scanning for Internet connection;

transmitting or receiving data over

the Internet

Green

: Connected to Internet

5

WIRELESS

Amber

: WPS function is enabled.

Green

: Wi-Fi wireless interface is

active now.

6

Extra

for

future use

not activated yet, function to be defined

Page 10 / 70

7

Rear Panel

The CH6640E (shown above) rear panel contains the following cabling port and

connectors:

Item

Description

1

TEL 1

TEL 2

VoIP connection for a single telephone. Two sets of telephone can be

supported.

2

ETHERNET

1

2

3

4

Use any Ethernet port to connect an Ethernet-equipped computer, hub,

bridge, or switch using an RJ-45 cable.

Activity LED

- Green LED defines the activity of the Ethernet connector.

When LED is ON, this indicates that there is no data traffic and a

connection is stabilized.

When LED is FLASHING, this indicates that there is data being

transmitted upstream or downstream.

When LED is OFF, this indicates that the unit is not powered or there is no

Ethernet connection.

3

RESET

Press and hold the RESET button for five seconds or longer to restore

CH6640E/CG6640E to factory default settings. After factory default

settings are restored, the gateway will restart and may take 5 to 30

minutes to find and lock on the appropriate communication channels.

4

USB

USB host port for print server or network storage function

5

CABLE

Connect the CH6640E/CG6640E to a cable wall outlet.

6

POWER

SWITCH

Switch gear for power on/off the CH6640E/CG6640E.

7

POWER

Provide power to the CH6640E/CG6640E.

Rate

Popular CBN Inc Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share