Calix 844G-1 Router Manual PDF (Setup & Configuration Guide)

Page 46 / 54 Scroll up to view Page 41 - 45

46

LED Behavior

Before leaving the site, verify that the GigaCenter is communicating with the

GPON network. Viewing the LEDs helps the installer determine the exact

state of the device.

A properly installed and functional GigaCenter exhibits the following LED

behavior:



When power is initially applied, the power LED behaves differently based

on the state/status of the UPS:



If no UPS is present or if a UPS is present and is not currently

providing primary power, the power LED illuminates and remains lit.



If a UPS is present and a battery alarm condition exists, the power

LED blinks to indicate an alarm status.



If LED does not light, power is off or the UPS power supply is not

functional.



During initial power-up, all remaining LED's come on momentarily

(lamp test).



If the SC-APC pigtail is not connected, the Phone 1 LED will begin to

blink when Voice Smart Activate is activated.



If the SC-APC pigtail is connected, the Broadband LED begins flashing

once downstream synchronization has been completed. The LED

switches to solid green if the GigaCenter has been provisioned.



As Ethernet ports are initialized, the corresponding LED illuminates

provided an Ethernet device is connected to the port.

Note:

Phone service is not available until the Broadband LED lights and

remains on.

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

Page 47 / 54

47

Note:

The integrated WPS feature allows for the sync'ing of remote WIFI

capable products with the GigaCenter. When in WPS mode (pressing the

WPS button), the WIFI LED blinks rapidly for 120 seconds, indicating the

remote device is attempting to pair with the GigaCenter.

Note:

By default, the Wi-Fi radio is disabled upon start-up. Once initialized

(via graphical user interface), the Wi-Fi LED assumes normal functionality).

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

Page 48 / 54

48

LED States and Status

The LED's located on the face of the GigaCenter provide information on the

status and current state of the device.

LED States and Status

LED NAME

ON

OFF

BLINK

POWER

Main AC power (either power adapter or

UPS) is present at the ONT/RSG.

No power present

(AC power or

battery back-up).

ONT/RSG is on battery and the

battery remains in a fully

functional state.

BROADBAND

Broadband physical connection has

been established. GigaCenter has

ranged with GPON network.

Broadband

interface is not

powered - no

signal detected.

When WAN is active, broadband

interface has detected a carrier

signal. LED blinks at 50% duty

cycle when optical light is

detected and the GigaCenter is i

ranging mode.

SERVICE

See table below for specific behaviors

WiFi 2.4 GHZ

WiFi 5 GHz

Wi-Fi is enabled.

Wi-Fi is disabled.

N/A

ETHERNET 4

through

ETHERNET 1

A powered device is connected to the

port.

The GigaCenter is

not powered,

cable is not

attached, or no

powered device is

connected to the

port.

Activity is present on associated

device - downstream traffic

present. Rate of blink loosely

translates to the amount of

packets being transported.

PHONE 1

PHONE 2

At least one POTS port is off hook.

Zero POTS ports

are in service (off

hook)

Smart Activate or Voice Activate

in process.

USB

A device is connected, and associated

with the USB port however the port is

currently idle.

The device is not

powered, no cable

connected, or no

powered devices

connected to the

port.

Activity is present on the USB

port. Rate of blink loosely

translates to the amount of

packets being transported.

RF

Model 854-1 AND

854-2 only

RF video optical level is within

prescribed AGC range.

RF Video optical

level is outside

prescribed range

(too low) or no

signal is present.

N/A

WPS

GREEN: On for three minutes or until

WPS button is pressed again.

RED: On for two minutes. An error has

occurred unrelated to security such as

no partner found, protocol aborted.

Press WPS button again to restart.

WPS function.

The device is not

currently in WPS

mode and is

waiting for the

attempt.

GREEN: The Wi-Fi protected

setup PBC procedure is in

progress.

RED: Session overlap detected

(security risk). Wait for 2 minutes

then press WPS button again to

restart. If error persists, refer to

PIN-based configuration method

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

Page 49 / 54

49

Service LED States and Status

LED

Appearance

Bridged Mode

RG Mode

Mixed Mode

OFF*

No Ethernet port has been

provisioned

No IP address has been

received or PPPoE session

authentication has not

occurred.

N/A

Solid GREEN

(Indicates internet

service)

At least one Ethernet port

has been provisioned.

The GigaCenter has

received an IP addressed or

a PPPoE session

authentication (with

credentials) has been

completed.

Same as RG Mode

Solid RED

N/A

GigaCenter attempted to

connect via IP and failed

(DHCP/PPPoE response or

authentication failed)

Same as RG Mode

* For all modes, the Service Gateway is not powered and a physical broadband connection has not been detected.

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

Page 50 / 54

50

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

Rate

Popular Calix Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share