WBMR-G54 Wireless ADSL Router User Guide

RIP

The Router supports RIP v1 and RIP v2 used to share routing tables with other Layer 3 routing devices on your local

network or remote LAN.

RIP System Wide Configuration window

To enable RIP, select

Enabled

from the

RIP

pull-down menu, select the

Protocol

(

RIPv1

and

RIPv1 Compatible

) and

Direction

(

In

,

Out

, or

Both

), and click

Apply

.

The RIPv1 Compatible option will transmit RIPv2 broadcast packets and receive both RIP v1 and RIP v2 packets.

The direction configuration refers to the RIP request. Select In to allow RIP requests from other devices. Select Out to

instruct the Router to make RIP requests for routing tables from other devices. Select

Both

to share routing tables in

both directions.

71

Downloaded from

www.Manualslib.com

manuals search engine

WBMR-G54 Wireless ADSL Router User Guide

ADSL

The

ADSL Configuration

window allows the user to set the configuration for ADSL protocols. For most ADSL

accounts the default settings

ADSL2+(Multi-mode)

will work. This configuration works with all ADSL

implementations. If you have been given instructions to change the Modulation method used, select the desired option

from the

Modulation Type

drop-down menu and click the

Apply

button.

72

Downloaded from

www.Manualslib.com

manuals search engine

WBMR-G54 Wireless ADSL Router User Guide

ADSL Configuration window

73

Downloaded from

www.Manualslib.com

manuals search engine

WBMR-G54 Wireless ADSL Router User Guide

ATM VCC

The

ATM VC Setting

window is used to configure the WAN connection. If you are using multiple PVCs, you can

change the configuration of any PVC in this window. To create new or additional PVCs, read the section on Multiple

PVCs on page 53.

This window can be used as an alternative to configure the same settings found on the WAN Settings window in the

Home

directory.

ATM VC Setting window

To configure an existing PVC configuration set, click the corresponding notepad icon in the right-hand column of the

ATM VCs List. The PVCs current settings appear above in the entry fields of the

ATM VC Setting

window. Configure

the appropriate settings and click the

Apply

button to put the new settings into effect.

74

Downloaded from

www.Manualslib.com

manuals search engine

WBMR-G54 Wireless ADSL Router User Guide

QoS

QoS or Quality of Service is used to allot priority from the Router. This is done by allotting a priority from a port to a

PVC. There are four priorities for each QoS configuration. “1” denotes the highest priority while “4” is the lowest.

The

IGMP Proxy/Snooping

is Disabled by default. This setting will not allow IGMP (Internet Group Management

Protocol) packets to be forwarded to the LAN. IGMP is used to manage multicasting on TCP/IP networks, most users

will not need to enable this. Some ISPs use IGMP to perform remote configuration for client devices, such as the

Router. If you are unsure, check with your ISP. To enable IGMP service to the LAN interface, select Enabled and click

the

Apply

button

QoS Configuration window

To set QoS for the router, first click the

PortMapping QoS

check box in the middle of the window. This will open the

following window. Then select the PVC to associate with the corresponding port and choose a priority for this

combination. The user may also enable IGMP Proxy/Snooping for each PVC at the top of the window by choosing the

PVC from the pull-down menu and clicking the

Enabled

radio button, set a maximum

Bandwidth

in kbps from

Auto

to

1024

using the drop-down menu. Click

Apply

to set the configuration.

75

Downloaded from

www.Manualslib.com

manuals search engine