1. Home
    2. /
  2. Manuals
    3. /
  3. Binatone
    4. /
  4. WR1500N2
    5. /
  5. 3
Page 11 / 73 Scroll up to view Page 6 - 10
WR1500N
150Mbps Wireless N Router
Chapter 2.
Connecting the Router
2.1 System Requirements
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is
connected directly to the Ethernet.)
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
TCP/IP protocol on each PC
Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari
2.2 Installation Environment Requirements
Place the Router in a well ventilated place far from any heater or heating vent
Avoid direct irradiation of any strong light (such as sunlight)
Keep at least 2 inches (5 cm) of clear space around the Router
Operating Temperature: 0
~40
(32
~104
)
℃
℃
±
±
Operating Humidity: 10%~90%RH, Non-condensing
2.3 Connecting the Router
Before installing the Router, make sure your PC is connected to the Internet through the
broadband service successfully. If there is any problem, please contact your ISP. After that, please
install the Router according to the following steps. Don't forget to pull out the power plug and keep
your hands dry.
1.
Power off your PC, Cable/DSL Modem, and the Router.
2.
Locate an optimum location for the Router. The best place is usually at the center of your
wireless network.
3.
Adjust the direction of the antenna. Normally, upright is a good direction.
4.
Connect the PC(s) and each Switch/Hub in your LAN to the LAN Ports on the Router, shown
in Figure 2-1. (If you have the wireless NIC and want to use the wireless function, you can
skip this step.)
5.
Connect the DSL/Cable Modem to the WAN port on the Router, shown in Figure 2-1.
6.
Connect the power adapter to the power socket on the Router, and the other end into an
electrical outlet. Press the power switch, and then the router will start to work.
7.
Power on your PC and Cable/DSL Modem.
- 5 -
Downloaded from
www.Manualslib.com
manuals search engine
Page 12 / 73
WR1500N
150Mbps Wireless N Router
Figure 2-1
Hardware Installation of the WR1500N 150Mbps Wireless N Router
2.3.1 Repeater Mode
After finishing the steps above, please choose the operation mode you need and carry out the
corresponding steps.
WR1500N is used to extend the range of wireless signal of the existing AP or wireless router.
On this mode, the only wired port works as LAN. Computer could connect to the device by either
wired or wireless way. The SSID of WR1500N should be the same as that of the device you repeat.
To avoid the conflict of DHCP service with front-end devices, the DHCP server is default to be
closed on this mode. If you want to log in the management page, please set your computer’s IP
address manually.
1.
Plug the power plug of WR1500N in electrical wall socket.
2.
Power on the notebook(s).
Note:
It is recommended that you connect a PC/notebook to the LAN port of the Router with an Ethernet
cable, and then login the Router from the PC/notebook to set the Router in AP Repeater mode.
- 6 -
Downloaded from
www.Manualslib.com
manuals search engine
Page 13 / 73
WR1500N
150Mbps Wireless N Router
Chapter 3.
Quick Installation Guide
This chapter will show you how to configure the basic functions of your WR1500N 150Mbps
Wireless N Router using
Quick Setup
Wizard
within minutes.
3.1 TCP/IP Configuration
The default IP address of the WR1500N 150Mbps Wireless N Router is 192.168.0.1. And the
default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide,
we use all the default values for description.
Connect the local PC to the LAN ports of the Router. And then you can configure the IP address
for your PC in the following two ways.
Configure the IP address manually
1)
Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this,
please refer to
Appendix B: Configuring the PC
.
2)
Configure the network parameters. The IP address is 192.168.0.xxx ("xxx" is any number
from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.0.1 (The
Router's default IP address).
Obtain an IP address automatically
1)
Set up the TCP/IP Protocol in "
Obtain an IP address automatically
" mode on your PC.
If you need instructions as to how to do this, please refer to
Appendix B: Configuring the
PC
.
2)
Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the
command prompt
to verify the network connection
between your PC and the Router. The following example is in Windows XP.
Open a command prompt, and type
, and then press
Enter
.
If the result displayed is similar to the Figure 3-1, it means the connection between your PC
and the Router has been established well.
Figure 3-1
Success result of Ping command
If the result displayed is similar to the Figure 3-2, it means the connection between your PC
and the Router is failed.
- 7 -
Downloaded from
www.Manualslib.com
manuals search engine
Page 14 / 73
WR1500N
150Mbps Wireless N Router
Figure 3-2
Failure result of Ping command
Please check the connection following these steps:
1.
Is the connection between your PC and the Router correct?
Note:
The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter
should be lit.
2.
Is the TCP/IP configuration for your PC correct?
Note:
If the Router's IP address is 192.168.0.1, your PC's IP address must be within the range of
192.168.0.2 ~ 192.168.0.254.
3.2 Quick Installation Guide
With a Web-based utility, it is easy to configure and manage the WR1500N 150Mbps Wireless N
Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web
browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1.
To access the configuration utility, open a web-browser and type in the default address
in the address field of the browser.
Figure 3-3
Log in the Router
After a moment, a login window will appear, similar to the Figure 3-4. Enter
admin
for the
User Name and Password, both in lower case letters. Then click the
OK
button or press the
Enter
key.
- 8 -
Downloaded from
www.Manualslib.com
manuals search engine
Page 15 / 73
WR1500N
150Mbps Wireless N Router
Figure 3-4
Login Window
s
Note:
If the above screen does not pop-up, it means that your Web-browser has been set to a proxy.
Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears,
cancel the Using Proxy checkbox, and click OK to finish it.
2.
After successfully log in, you can click the
Quick Setup
menu to quickly configure your
Router.
Figure 3-5
Quick Setup
3.
Click
Next
, and then
WAN Connection Type
page will appear, shown in Figure 3-6.
Figure 3-6
WAN Connection Type
The Router supports three popular ways
PPPoE
,
Dynamic IP
and
Static IP
to connect to the
Internet. Please make sure of what kind of connection type your ISP provides, and then select
the very type and click
Next
to go on configuring.
- 9 -
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Popular Binatone Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top