Billion BiPAC-7404VNOX Router Manual PDF (Setup & Configuration Guide)

Given below is full router user manual of Billion BiPAC-7404VNOX router model. You can also download this manual in PDF Format to read later on your computer.

Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.

Page 1 / 9
BiPAC 7404VNOX
BiPAC 7404VNPX
3G/ VoIP/ 802.11n ADSL2+
(VPN) Firewall Router
Quick Start Guide
Page 2 / 9
Page 3 / 9
Billion BiPAC 7404VNOX/7404VNPX 3G/VoIP/802.11n ADSL2+ (VPN) Firewall Router
-
1-
Package Contents
BiPAC 7404VNOX/ 7404VNPX ADSL2+ Router
CD containing the on-line manual
RJ-11 ADSL/ telephone cable
Ethernet (RJ-45) cable
Three 2dBi detachable antennas
Power adapter
PS2-RS 232 console cable
Quick Start Guide
Splitter/ Micro-filter (Optional)
Warning
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.
°
Do not use the router in high humidity or high temperatures.
°
Do not use the same power source for the router as other
equipment.
°
Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
°
Avoid using this product and all accessories outdoors.
°
Place the router on a stable surface.
°
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Attention
Page 4 / 9
Quick Start Guide
-
2-
Hardware Overview
The Front LEDs
The Rear Ports
* Note: For WPS configuration, please refer to the WPS section of User Manual.
Connect it with the
supplied power
adapter.
Connect to the ADSL /
telephone network with
RJ-11 cable (telephone).
Press the RESET
button for 6
seconds and
above to restore
the factory
default settings.
Connect to a PC or an
office/ home network
of 10/100/1000Mbps
with UTP Ethernet
cable.
Connect with
the detachable
antennas.
Connect to the
telephone jack on the
wall with RJ-11 cable.
Connect to an
analog phone set
with RJ-11 cable.
Lit when connected to an
Ethernet device.
Lit Green for 1000Mbps;
Orange for 100Mbps; but
no light for 10Mbps.
Blinks when data is being
Transmitted / Received.
Lit green
when the
phone is
off hook
Lit Green when
successfully
connected to an
ADSL DSLAM,
(“line sync”).
Lit green when a
wireless connection
is established.
Flashes green when
the device is sending/
receiving data.
Lit green when the
USB device is ready.
Flashes when data is
being transmitted /
received.
Power
ON/OFF
switch
Lit red when WAN port fails
to get IP address. Lit green
when WAN port gets IP
address successfully. Unlit
when device is in bridged
mode or WAN connection
not present.
Lit green when the
inbound and outbound
calls are transmitted
through PSTN.
Lit green when SIP
registration is ok for
phone 1 or orange for
phone 2. When
registration for both
phone 1 & 2 are ok, both
green and orange light
will be lit together.
Push to trigger Wi-Fi
Protected Setup
function. *
3G/ HSDPA USB
modem backup for
Internet access
Lit orange/ red when
power is ON. Lit red
means system has
failed. Lit green when
the system is ready.
Page 5 / 9
Billion BiPAC 7404VNOX/7404VNPX 3G/VoIP/802.11n ADSL2+ (VPN) Firewall Router
-
3-
Hardware Connection
Hardware Installation
1. Power Connection
Plug the supplied power adapter in to the wall jack and the other side to the router.
Please note that the plug type may differ according to country.
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the
other side to the PC’s Ethernet interface.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top