1. Home
    2. /
  2. Manuals
    3. /
  3. Billion
    4. /
  4. BiPAC-7404VGO
    5. /
  5. 4
Page 16 / 155 Scroll up to view Page 11 - 15
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router
Chapter 3: Basic Installation
15
Configuring PC in Windows 95/98/ME
1.
Go to
Start / Settings / Control Panel
. In the Control Panel,
double-click
Network
and choose the
Configuration
tab.
2.
Select
TCP / IP -> NE2000 Compatible
, or the name of any
Network Interface Card (NIC) in your PC. (
See Figure 3.9)
3.
Click
Properties
.
4.
Select the
IP Address
tab. In this page, click the Obtain an IP
address automatically radio button. (
See Figure 3.10)
5.
Then select the
DNS Configuration
tab.
(See Figure 3.11)
6.
Select the
Disable DNS
radio button and click
OK
to finish
the configuration.
Figure 3.9: TCP / IP
Figure 3.10: IP Address
Figure 3.11: DNS Configuration
Page 17 / 155
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router
Chapter 3: Basic Installation
16
Configuring PC in Windows NT4.0
1.
Go to
Start / Settings / Control Panel
. In the
Control
Panel, double-click
Network
and choose the
Protocols
tab.
2.
Select
TCP/IP Protocol
and click
Properties
. (
See Figure
3.12)
3.
Select the
Obtain an IP address from a DHCP server
radio
button and click
OK
. (
See Figure 3.13)
Figure 3.12: TCP / IP
Figure 3.13: IP Address
Page 18 / 155
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router
Chapter 3: Basic Installation
17
Factory Default Settings
Before configuring your, you need to know the following default settings.
Web Interface (Username and Password)
Username: admin
Password: admin
The default username and password are “
admin
” and “
admin
” respectively.
Device LAN IP settings
IP Address: 192.168.1.254
Subnet Mask: 255.255.255.0
ISP setting in WAN site
PPPoE
DHCP server
DHCP server is enabled.
Start IP Address: 192.168.1.100
IP pool counts: 100
LAN and WAN Port Addresses
The parameters of LAN and WAN ports are pre-set in the factory.
The default values are shown below.
WAN Port
IP address
192.168.1.254
Subnet Mask
255.255.255.0
DHCP server function
Enabled
IP
addresses
for
distribution to PCs
100 IP addresses continuing from
192.168.1.100 through 192.168.1.199
The PPPoE function is
enabled
to automatically get the WAN
port configuration from the ISP.
Attention
If you ever forget the username/password to login to the router, you may
press the RESET button up to 6 seconds to restore the factory default
settings.
Caution
: After pressing the RESET button for more than 6 seconds, to be sure you power
cycle the device again.
Attention
Page 19 / 155
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router
Chapter 3: Basic Installation
18
Information from your ISP
Before configuring this device, you have to check with your ISP (Internet Service Provider) to find out
what kind of service is provided such as DHCP (Obtain an IP Address Automatically, Static IP (Fixed IP
Address) and PPPoE.
Gather the information as illustrated in the following table and keep it for reference.
VPI/VCI, VC / LLC-based multiplexing, Username, Password, Service Name,
and Domain Name System (DNS) IP address (it ca be automatically assigned
by your ISP when you connect or be set manually).
VPI/VCI, VC / LLC-based multiplexing, Username, Password, Service Name,
and Domain Name System (DNS) IP address (it ca be automatically assigned
by your ISP when you connect or be set manually).
In addition, additional
WAN address can be assigned using PPPoE dialer.
VPI/VCI, VC / LLC-based multiplexing, Username, Password and Domain
Name System (DNS) IP address (it ca be automatically assigned by your ISP
when you connect or be set manually).
VPI/VCI, VC / LLC-based multiplexing to use Bridged Mode.
VPI/VCI, VC / LLC-based multiplexing, IP address, Subnet mask, Gateway
address, and Domain Name System (DNS) IP address (it is a fixed IP
address).
VPI/VCI, VC / LLC-based multiplexing, IP address, Subnet mask, Gateway
address, and Domain Name System (DNS) IP address (it is a fixed IP
address).
Page 20 / 155
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router
Chapter 3: Basic Installation
19
Configuring with your Web Browser
Open your web browser, enter the IP address of your router, which by default is
192.168.1.254
, and click
“
Go
”, a user name and password window prompt will appear.
The default username and password
are “admin” and “admin”
respectively
. (See Figure 3.14)
Figure 3.14: User name & Password Prompt Widonw
Congratulation! You are now successfully logon to the VoIP/(802.11g) ADSL Router!

Rate

124.8 / 5 based on 304 votes.

Popular Billion Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top