Billion BiPAC-7401VGP Router Manual PDF (Setup & Configuration Guide)

Page 111 / 120 Scroll up to view Page 106 - 110

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

The following MIBs are supported:

¾

From RFC 1213 (MIB-II):

;

System group

;

Interfaces group

;

Address Translation group

;

IP group

;

ICMP group

;

TCP group

;

UDP group

:

EGP (not applicable)

;

Transmission

;

SNMP group

¾

From RFC1650 (EtherLike-MIB):

;

dot3Stats

¾

From RFC 1493 (Bridge MIB):

;

dot1dBase group

;

dot1dTp group

;

dot1dStp group (if configured as spanning tree)

¾

From RFC 1471 (PPP/LCP MIB):

;

pppLink group

:

pppLqr group

¾

From RFC 1472 (PPP/Security MIB):

;

PPP Security Group)

110

Page 112 / 120

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

¾

From RFC 1473 (PPP/IP MIB):

;

PPP IP Group

¾

From RFC 1474 (PPP/Bridge MIB):

;

PPP Bridge Group

¾

From RFC1573 (IfMIB):

;

ifMIBObjects Group

¾

From RFC1695 (atmMIB):

;

atmMIBObjects

¾

From RFC 1907 (SNMPv2):

;

only snmpSetSerialNo OID

111

Page 113 / 120

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

IGMP

IGMP, known as

Internet Group Management Protocol

, is used to management hosts from

multicast group.

IGMP Forwarding:

Accepting multicast packet.

Default is set to

Enable.

IGMP Snooping:

Allowing switched Ethernet to check and make correct forwarding decisions.

Default is set to

Enable.

VLAN Bridge

This section allows you to create VLAN group and specify the member.

Edit:

Edit your member ports in selected VLAN group.

Create VLAN:

To create another VLAN group.

Advanced VLAN Setup Example (Triply Play)

VLAN_data:

Ethernet Port 1, Wireless and Wireless WDS are reserving for Internet

- On Ethernet port 1 I also need VC 0/40 bridged.

VLAN_Vedio

Ethernet ports: 2, 3 and 4:

-

0/33 Bi-directional IP

-

0/34

Video

-

0/35

Video

-

0/36

Video Subscriber Services (EPG, EAS, etc.)

-

0/37

Video

-

0/38

Video

-

0/39

Spare

Step 1: Setup Member Ports

Go to

Configuration

Æ

LAN

Æ

Bridge Interface.

You can setup member ports for each VLAN group under Bridge Interface section. From the

example, two VLAN groups need to be created.

Ethernet: P1 (Port 1)

Ethernet1: P2, P3 and P4 (Port 2, 3, 4) Please uncheck P2, P3, P4 from Ethernet VLAN Port first.

Note:

You should setup each VLAN group with caution.

Each Bridge Interface is arranged in this

order.

112

Page 114 / 120

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

113

Ethernet

P1 / P2 / P3 / P4

Ethernet2

P3 / P4

Step 2: Create WAN Interface

Go to

Configuration

Æ

WAN

Æ

ISP

wanlink

is the factory default WAN interface which in service for data/internet access. If your ISP

uses this access protocol, click

Edit

to input other parameters if needed.

If your ISP does not use

PPPoE, you can change the default WAN connection entry by clicking

Change

.

From the example, 0/40 is used for data/internet and assumes PPPoE is used; click the

Edit

to

change the VPI/VCI to 0/40.

Click

Create

to setup up additional WAN interface for video applications. Total of 8 VLAN is

support; therefore, only 8 WAN interfaces can be created in the table.

From the example, PVC 0/33 to 0/39 is assigned for video using 1483 Bridged mode.

Check

RFC

1483 Bridged

and click

Spaces next to VPI and VCI, type 0 and 33 in respectively. Select appropriate ATM Class,

Encapsulation Method, Acceptable Frame Type, Filter Type and PVID for Untagged Frames.

Page 115 / 120

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

VPI and VCI:

Enter the information provided by your ISP.

ATM Class:

The Quality of Service for ATM layer.

Encapsulation method:

Select the encapsulation format, this is provided by your ISP.

Acceptable Frame Type:

Specify what kind of traffic can through this connection, all traffic or only

VLAN tagged.

Filter Type:

Specify the type of ethernet filtering performed by the named bridge interface.

All

Ip

Allows only IP/ARP types of ethernet packets through the port.

Pppoe

Allows only PPPoE types of ethernet packets through the port.

PVID for Untagged Frames:

PVID is known as Port VLAN Identifier. When an untagged packet

is received by input port(s), this packet will be tagged with specified PVID.

From the example, VPI and VCI only section need to be filled-in and just leave the rest as is.

Repeat the same procedure by clicking

Create

Æ

select

RFC1483 Bridged

Æ

fill-in the rest of

PVC 0/34 to 0/39.

Step 3: Setup VLAN Service

Go to

Configuration

Æ

Advanced

Æ

VLAN Bridge

114

DefaultVlan

lists all member ports.

It is necessary to group specific member ports for each VLAN.

Rate

Popular Billion Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share