Billion BiPAC-7401VGP Router Manual PDF (Setup & Configuration Guide)

Page 86 / 120 Scroll up to view Page 81 - 85

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

Here are some Examples for your reference:

xxx

Any 3 digit number only between 0 and 9.

Total length is 3.

Note: No period is needed (.)

123x

.

Any number (0-9) starting with 123. Maximum length is 16.

[x-x]x

.

For example: [1-3]x

.

Any number (0-9) starting with number 1 to 3. Maximum

length is 16.

85

Page 87 / 120

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

Ring & Tone

This section allows advanced user to change the existing or newly defined parameters for

the various ring tones (dial tone, busy tone, answer tone and etc.)

Country Specific Ring & Tone

Region:

Select a country ring-tone, from the drop-down list, where you are located. This VoIP

router provides default parameter of ring tones according to different countries.

The ring-tone

parameters are automatically displayed after entering a specific country.

If your country is not in

the list, you may manually create ring-tone parameters.

Ring Parameters

Ring Cadence (in ms):

Ring cadence is defined by three fields, Frequency: On Time1, Off Time1,

On Time2, Off Time2 and On Time3, Off Time3. Frequency is specified in Hertz. Time is given in

milliseconds.

Tone Parameters

You may need to check with your local telephone service provider for such information. Also, it is

recommended that this option be configured by an advanced user, unless you are instructed to do

so.

Click

Apply

to apply the settings.

86

Page 88 / 120

VoIP/(802.11g) ADSL2+ Router

Special dial codes

The following table lists the special dial codes that are built-in to the system:

Option

Description

Flash-hook

(Wireless Router with LINE

port only)

Switch to PSTN line

Note: A quick press of the hook. On some phones a button is provided

which provides Flash-hook functionality. The button is marked "FLASH"

or "RECALL".

*69

Return the last missed call for SIP service only

Note: Entering this on a phone will call the last number which made a

call to the phone. For example A makes a call to B, but hangs up before

B answers. If B enters *69, A will be called.

##

Last number redial

*20

Set do not disturb on

Note: It is possible to set a Do-Not-Disturb feature on a phone such that

any phone which calls the phone will receive an engaged tone and the

phone called will not ring. For example, B enters *20 and hangs up. A

makes a call to B, and receives the engaged tone and phone B does not

ring.

*80

Set do not disturb off

*74<x><number>#

Set the number for Speed dial code ‘x’, where ‘x’ is a

number between 2 and 9.

Note: Where <x> is a number between 2 and 9, and <number> is the

number to dial. The code needed to dial a speeddial from a phone

connected to a VoIP Router is:

<

x

>#, where

<x>

is a number between 2 and 9.

The settings will infect to your setting in Speed Dial on WEB GUI.

*90<phone-number>

Set the number for performing

Blind Call Transfer

, where

<phone-number> is the number that you wish to transfer the

call to. It’s for SIP service only.

Note: In

Blind Call Transfer

, you have a call in progress (incoming or

outgoing) and decide you wish to transfer the call to another phone. To

transfer the call, perform the following steps:

1. Hook-flash to get a dial tone.

2. Dial *90<phone-number> (e.g. *907401), there will be a confirmation

tone then hang up. The other end will hear ring back and the called third-

party phone will ring. When the third-party phone is picked up the two

calls will be connected.

If the third-party phone does not answer then the caller being transferred

can hang up to cancel the connect attempt.

87

Chapter 4: Configuration

Page 89 / 120

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

QoS (Quality of Service)

QoS function helps you to control your network traffic for each application from LAN (Ethernet and/or

Wireless) to WAN (Internet).

It facilitates you to control the different quality and speed of through put for

each application when the system is running with full loading of upstream.

You can find three items under the

QoS

section:

Prioritization

and

Outbound / Inbound IP Throttling

(bandwidth management).

88

Page 90 / 120

VoIP/(802.11g) ADSL2+ Router

Chapter 4: Configuration

Prioritization

There are three priority settings to be provided in the Router:

~

High

~

Normal

(The default is normal priority for all of traffic without setting)

~

Low

And the balances of utilization for each priority are High (60%), Normal (30%) and Low (10%).

Click Clear

You can click

Clear

to delete the existing Application.

Application

: A user-define description to identify this new policy/application.

Time Schedule

: Scheduling your prioritization policy.

Priority

: The priority given to each policy/application. Its default setting is set to High; you may

adjust this setting to fit your policy/application.

Protocol

: The name of supported protocol.

Source Port

: The source port of packets to be monitored.

Destination Port

: The destination port of packets to be monitored.

Source IP Address Range

: The source IP address or range of packets to be monitored.

Destination IP address Range

: The destination IP address or range of packets to be monitored.

DSCP Marking

: Differentiated Services Code Point (DSCP), it is the first 6 bits in the ToS byte.

DSCP Marking allows users to classify traffic based on DSCP value and send packets to next

Router.

See Table 4. Here is the DSCP Mapping Table:

89

Rate

Popular Billion Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share